Question about Kenwood Excelon KAC-X811D Car Audio Amplifier

2 Answers

Error code 02

The amp pops when I turn the car on and then this message flashes. Every now and then it works just fine. How can I fix?

Posted by on

  • 1 more comment 
  • Gueits Mar 27, 2008

    Thx

  • kulwip2008 Aug 31, 2008

    mine amplifier is saying e 02. so will it need to be repaired? if so what is the absolute problem?

  • shahzad_rwp May 08, 2009

    I HAVE THE SAME PROBLEM OF ERR 02.RED LIGHT IS BLINKING & ITS NOT WORKING

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 290 Answers

According to the manual, error code 02 is displayed when there is DC on the speaker outputs (which should normally never happen). Unless one of the speaker wires is touching +12V or ground, the issue is probably inside the amp itself and will need repair.

Posted on Mar 27, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My amp was doing it and i let it cool down and had a bigger fan put in it and now it doesnt do it anymore

Posted on Jun 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When installed, amp gets power but produces no sound


If you have a small mom and pop shop in your area. I would have them check it out. You might have gotten lucky.

Mar 28, 2014 | Sony Exm-502 Mosfet 2 Channel Stereo...

1 Answer

When i turn up the volume to a certain point my subs pop.


low Ohm speaker configuration or bad current intake. how many speakers you have on it? what size of power cables you use?

Jun 01, 2010 | MTX Terminator TN400/4 Car Audio Amplifier

1 Answer

Amp turns on fine hooked up to factory cd player when u turn volume up red light pops on on amp


it means there not enough power going to the amp.or the power wire inside the amp has melted resalting in a bad conection

Dec 29, 2009 | Sony Xplod XM-1652Z Car Audio Amplifier

1 Answer

Mrv F345 power cut out and now the screen flashes blue


disconnect all of the speaker wires at the amp and turn your system on -if the amp stays on then you likely have a roasted coil in one of your speakers somewhere and causing a short which is shutting your amp down into protection mode-if the amp wont stay on with nothing connected to it then you have probably roasted something inside the amp and uhhh good luck bro

May 09, 2009 | Alpine MRV-F345 Car Audio Amplifier

1 Answer

My amplifier is not in protection mode everything works fine but my subwoofers play a very small sound . and it is not my subs at fault i already tested my subs and they work fine. i know theres a problem...


THERES A PROBLEM WITH YOUR RCA'S,IF YOU JIGGLE THEM WHILE THERE HOOKED UP TO THE AMP AND THEY MAKE THINGS LOUDER OR POP THAN YOU NEED TO GET THE RCA TERMINALS FIXED.

May 07, 2009 | Crunch Maxxsonics PZi 3000.1D Car Amp

1 Answer

Noise


that is a bad ground clean exsisting ground or find a new spot where the ground is no longer than 18" if possible

Mar 24, 2009 | Car Audio & Video

1 Answer

Moisture in amp while on, caused a small pop, then no sound outpu


check the fuse between the battery and the amp. (not the fuse in the back of the amp).
if that doesn't work then something on the inside of the amp is fried.

Jan 30, 2009 | Phoenix Gold Xenon-200.4 Car Audio...

1 Answer

Infinity Reference 7541a protect & Clip lights come on


Hello pianopeter, I have the same amp with the same problem but only when the crossover mode switch on the front channel is set to low pass or high pass. Have'nt fixed that yet cause when I got the amp and put power to it the clip and protect lights would flash back and forth. I turned out to have 2 bad output transistors on the right front channel, I replaced them and amp works great now. Then when I was doing final testing I switched the crossover mode switch to lowpass and your problem occured. I do believe the problem is in the removable board which controls the controls the crossover and input to a point. Try moving the crossover mode switch to flat on both front and rear and let me know if amp works fine that way. I'll be working on this problem soon but would like to know if your problem changes if you move the switch to flat. Please leave me a message as soon as you find out cause this will aid in the process of me fixing problem. I am an electronics tech and buy and fix broken amps all the time so I have a really good knowledge of car amp repair. Once again let me know ASAP, Thanks

Jan 15, 2009 | Infinity Reference 7541a Car Audio...

1 Answer

Hooked my punch Punch P450.4 up to speakers and ran rca cables to front and it wont work


Hi Jon,  you need to hook the Remote wire up to the Radios  Blue remote wire.  The car battery power stays on all the time.  The blue Remote wire watches to see when the radio turns on, and signal the amp to turn on as well.

Dec 12, 2006 | Rockford Fosgate Punch P450.4 60W x 4 Car...

Not finding what you are looking for?
Kenwood Excelon KAC-X811D Car Audio Amplifier Logo

Related Topics:

359 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4724 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Pablo Gonzalez

Level 3 Expert

733 Answers

Are you a Kenwood Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...