Question about Hitachi 46F510 46" Projection HDTV

1 Answer

Blurry Where can I get a convergence kit and a repair manuel to fix it

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hitachi Master
  • 3,459 Answers

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....

  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
  • TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.
Here are some photos of convergence problems.

Blurry - 42d3683.jpg



e87380c.jpg
Here is a quick test....

Using your original remote go-to the settings menu then goto the convergence section.

Try to adjust the red and then the blue convergence.

You should be able to move RED and BLUE in all directions - up, down, left, and right. And you should be able to get the grid straight.

If you can't move them in all directions or cant move them far enough your convergence chips are bad and should be replaced. This is a common problem.

Note: If you TV has as flash focus or magic focus button only try pressing the button. If it fails to fix the convergence your need to fix it. See below for a fix

69189a5.pngCONVERGENCE SOLUTION

You can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Posted on Aug 14, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

We just got this hand-me-down SONY TV and when we turned it on the menu screen is not aligned, the color is distorted and video is blurry. We were told that it would be more expensive to fix than the TV...


Thats a convergence issue very common problem You can get the Sony Type 1 convergence repair kit from www.tvrepairworld.com which fits your model. The kit does come with repair instructions.

May 18, 2011 | Sony KP-51WS500 51" Rear Projection...

1 Answer

How do i fix blurry picture on 56 inch toshiba


Ur convergence is dead.Must know how to solders?Must replaced 2 convergence ICS,and some or all it resistors.Tries websites Tv repair World.com,Tvrepairkits.com to buy a cconvergence kit to repair it ur self.The shop will cost u $300 for parts and labors.

Mar 15, 2010 | RCA D52W20 52" Rear Projection HDTV-Ready...

1 Answer

Hi I have a 53 inch sony tv that seems to be blurry what can i do to fix this?


Convergence it dead.Know how to solders? Must replaced the 2 convergence IC and all it resistors.Tries Tv repair World.com,Tvrepairkits.com for the convergence kit to repair it ur self.The shop will cost U $300 for parts and labors.

Feb 04, 2010 | Televison & Video

1 Answer

Blurry,double exposure picture


Ur convergence is dead.Must replaced convergence ICS and all it resistors.U know how to solders?Buy a convergence kit at Websites Tv repair World.com,Tvrepairkit.com replaced what in the convergence kit.

Jan 11, 2010 | Mitsubishi WS-55809 55" Rear Projection...

1 Answer

Sony 51" Rear Projection TV is blurry with colored ghost images


Thats caused by a convergence failure. The Sony type 1 convergence repair kit from www.tvrepairworld.com will usually correct that issue the kit contains the components and the CD with repair instructions so you can repair yourself.

Dec 20, 2009 | Sony KP-46WT510 46" Rear Projection HDTV

1 Answer

Blurry picture on left side double image right side is ok....


Ur convergence is dead,need convergence kit.
U know how to solder right?Tries these websites for convergence kit.Tv Repair World.com,Shopjimmy.com,Ebay.com or Partstore.com

Sep 25, 2009 | Zenith IQB50M90W 50" Rear Projection...

1 Answer

I have an Hitachi 46F510. The picture is blurry. Mostly when words are on the screen (i.e. the menu).


The convergence is dead.U need a convergence kit.These websites have it.Tv Repair World.com and Shopjimmy.com.Buy the kit with ur tv model and fix it.

Sep 10, 2009 | Hitachi 46F510 46" Projection HDTV

1 Answer

3D blurry picture


The convergence ICs and resistors need replacement. The DPTV305-345 convergence repair kit works for most Phillips rear projection Tvs. The kit contains the two ICs 12 resistors and the CD with detailed instructions
http://www.tvrepairworld.com/

Jul 22, 2009 | Hitachi 43UWX10B 43" Rear Projection...

1 Answer

Double Images


Just click below for convergence repair kit;

http://servicemanuals.vstore.ca/

Double images and colors are blurry .Blue,red and yellow wave coming up from the bottom of the screen on the lower left symptom is for busted convergence IC,you must replaced this IC in order that will works better again.STK 392-xxx ICs and it's associated resistor,this resistor automatically change value,can caused truoble even though you change the ICs.If you bring this to a service center they cost you $600 to $700,but if you buy the repair kit you can save more,don't wory it is very easy because there is intallation guide including in the repair kit. Feel free to ask whatever the result... click the link for sample picture guide step by step installation;

Hope this may help;

Regards,
VOTIT

Oct 02, 2008 | Sony Grand WEGA KDP-65WS550 65" Rear...

Not finding what you are looking for?
Hitachi 46F510 46" Projection HDTV Logo

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hitachi Televison & Video Experts

Jaime Hernandez

Level 3 Expert

2318 Answers

The Knight
The Knight

Level 3 Expert

74251 Answers

matt martin
matt martin

Level 3 Expert

1210 Answers

Are you a Hitachi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...