Question about Computers & Internet

2 Answers

Foxconn F845DA jumper settings - Computers & Internet

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

JP1 PIN 1-2 = On board audio disable
JP1 PIN 2-3 = On board audio enable

JP2 = Temperature Sense connector

JP3 PIN 1-2 = Normal
JP3 PIN 2-3 = Clear CMOS

1. Power off the system and unplug the chassis AC power cord.
2. Short JP3 at PIN 2-3 for a few seconds.
3. Set JP3 back to it's normal position at pin 1-2.
4. Plug the AC power cord to the chassis.
5. Power on the system and load the BIOS setup default.

Posted on Apr 25, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 329 Answers

What seems to be the problem of you jumper settings?

Posted on Mar 26, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bios password for foxconn h61mxe


open up the case and look at the mb, look for cmos reset, you need to turn off the computer use the jumper to short out the board, when the jumper is in place turn the computer on let the system boot up than shut the system down remove the jumper, restart the computer.
if that fails you could try removing the back up battery on the board.

maybe try removing the battery on the motherboard first before resetting the cmos.

Feb 27, 2015 | Foxconn H61MXE-V...

1 Answer

Foxconn p4m800p7ma-rs2 motherboard on Gforce FX5500 system halted


You refer to Master/Slave disks. Are you actually using the Master/Slave jumper settings? Must motherboards and OSs today recommend putting the disks in the CABLE SELECT jumper setting. The problem with the old Master/Slave setting is that the Controller on the Master Disk is used to control the Slave disk as well. This can lead to problems when disks are made by different manufacturers, as sometimes they are not fully compatible. In CABLE SELECT, each disk controller works independently.

Dec 30, 2011 | Foxconn Computers & Internet

1 Answer

Changed cpu multiplier from 17 to 19 now have blank screen on foxconn a88gmx, cant reset as cannot access bios


Try clearing the CMOS --- the down side is your lose all your setting --- the up side is you should be
able to access your BIOS

Clear CMOS Jumper: CLR_CMOS1 ( Located near CMOS battery )
The motherboard uses CMOS RAM to store the basic hardware information (such as BIOS data,
date, time information, hardware password...etc.). Clear CMOS data is the fast way to go back to
factory default when the BIOS settings were mistakenly modified.
The steps to clear CMOS data are :
1. Turn off the computer, unplug the power cord from the power outlet.
2. Remove jumper cap from pins 2-3, put it onto pins 1-2 to short them.
This will clear CMOS data.
3. Return the setting to its original with pins 2-3 closed.
4. Plug in the power cord to your computer and turn it on.
5. Go to BIOS Setup to configure new system as described in next chapter.
Clear Jumper on pins 1 & 2
1 ----
2 ----
3
Normal
(Default)
1
2 ----
3 ----
CLR_CMOS1
  • Disconnect the power cable before adjusting the jumper settings.
  • Do not clear the CMOS while the system is turned on.
WARNING!
Jumper Diagram Definition Description
1-2 Set Pin 1 and Pin 2 closed
2-3 Set Pin 2 and Pin 3 closed

Feb 10, 2011 | Foxconn A88GMX AM3 AMD 880G HDMI Micro ATX...

1 Answer

Foxconn N 15235. From cold start cannot find boot device, after ctrl alt del it reboots. CMOS battery replaced. Problem persists. Only 1 HDD Sata and no CD Rom / FDD intalled


make jumper setting to your hdd u will see at the front of the hdd the jumper settings before u"ll do the job unflug the power supply

Jan 20, 2011 | Computers & Internet

1 Answer

I have a Foxconn motherboard and have just connected an additional internal HDD to the SATA1 socket but when I turn the computer on the new HDD is not found. Can you help?


Your new HDD might be higher speed than the motherboard support supported speed. Change the Jumper setting of HDD as per the manufacturer description.

Oct 05, 2010 | Foxconn 945GZ7MC-RS2H Motherboard

1 Answer

Foxconn a6vmx motherboard , just installed but no vga output?


Check the Motherboard to make sure that the jumpers on the motherboard are not set to disable the slot. Try the card in a different pc. Try a diffrent card in the same slot. That should tell you if it is
1.motherboard
2.slot
4.or card......
Good luck, hope this helps,
James.
PLEASE VOTE 4 THUMBS UP 4 ME!!!!!!

Apr 26, 2010 | Foxconn A6VMX Socket AM2+ AMD Motherboard...

1 Answer

No video output


Try to change the cmos jumper to the other side, some motherboard comes with this jumper set to clear so the cmos batt dont drain out on storage.

Jul 08, 2009 | Foxconn A7VMX-K Motherboard

1 Answer

CD Rom installation


the cdprom power cable port might be faulty plz check it ...

Jul 07, 2009 | Computers & Internet

4 Answers

Memory upgrade from ddr 256mb to ddr2 1g


there is a jumper setting to slect which type of memory you want to use, check your manual for details on how to change it

1> enusre the rams are in correctly
2>ensure your main board supports the amount of memory and the speed of the memory
3> verify jumper select to correct memory type is set correctly

if the main board aint compatable with the memory you brought that will cause the same problem

Jan 02, 2008 | Foxconn P4M800P7MA-RS2 Motherboard

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

549 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Brian Sullivan
Brian Sullivan

Level 3 Expert

27725 Answers

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...