Question about Fantom Vacums Cyclone XT Upright Vacuum

2 Answers

Circuit board i have searched far and wide looking for a circuit board for my fantom cyclone xt, so far i can't find one .. is their anyone who can can locate or sell me one of these hard to find items. i am at the end of my rope ! any help is appreciated, thank you for your time TOO SLIM

Posted by on

  • TOO SLIM Apr 10, 2008

    THANK YOU SO MUCH .... ITS WHAT I NEEDED THAT I COULDN'T FIND ANYWHERE ELSE..

    AGAIN THANKS

    TOO SLIM

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 8,617 Answers

You should be able to locate parts for your vacum at this link by entering the model number.
http://www.fantom.com/fantom/default.aspx

Posted on Mar 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Fantom F11063 Cyclone Vaccum


I think the manual can help you in replugging the wires

How did you pull out the wires from circuit board ?
Is it with professional help or through some other means



Sep 18, 2008 | Fantom Vacums Cyclone XT Upright Vacuum

1 Answer

How do i replace the belt in the Fantom Cyclone XT vacuum


remove the covers over the headlights and under the shiny foul. there are two screws. there are two tabs that hold down the cover over the wheels, they just pop on/off with a click.
on my xt. i had to remove the rolling brush and clean out all the hair that was stuck in the bearings. remove the screw holding down the motor and belt. pry out the roller brush to get to the bearings. there was some serious hair ball in there.
reassembled mine and it works perfectly now :)

Dec 19, 2008 | Fantom Vacums Cyclone XT Upright Vacuum

1 Answer

Parts


Hi,

TheFantom Cyclone XT was originally manufactured by Fantom Technologies,Inc. that closed in October 2001. The replacement for a Fantom CycloneXT would be Westinghouse Wired Deluxe Edition (either a WST1550 or a WST1551). These replacement products are now handled by Salton Inc. Perhaps you may inquire from them:
  • Salton Inc.
  • 1 800 616 8689
  • salton@saltonusa.com
Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Aug 20, 2008 | Fantom Vacums Cyclone XT Upright Vacuum

2 Answers

Fantom cyclone xt quit working in the middle of using it


you probably have a broken wire in cord or the power switch has gone bad two options take it to qualified electrical repair shop or if you just purchased it recently return it to the store also try another appliance in same outlet to make sure you havent thrown a circuit breaker hope this helps

Aug 20, 2008 | Fantom Vacums Cyclone XT Upright Vacuum

1 Answer

Fantom Cyclone wiring


Hi,

The only sure way recommended (and probably the safest) would beto get a service manual or at least a schematic diagram. The FantomCyclone XT was originally manufactured by Fantom Technologies, Inc.that closed in October 2001. The replacement for a Fantom Cyclone XTwould be Westinghouse Wired Deluxe Edition (either a WST1550 or a WST1551). These replacement products are now handled by Salton Inc. Perhaps you may inquire from them:
  • Salton Inc.
  • 1 800 616 8689
  • salton@saltonusa.com
Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Jun 08, 2008 | Fantom Vacums Cyclone XT Upright Vacuum

1 Answer

Fantom Cyclone XT


The top edge pieces will pop off, tabs hold them in place, then you take it apart.

May 27, 2008 | Fantom Vacums Cyclone XT Upright Vacuum

3 Answers

Fantom Cyclone XT


On each side of the top, on the back, there is a screw, take them out and the top will lift up from the back to the front. Then you can get to the belt.

Feb 10, 2008 | Fantom Vacums Cyclone XT Upright Vacuum

Not finding what you are looking for?
Fantom Vacums Cyclone XT Upright Vacuum Logo

Related Topics:

324 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fantom Vacums Vacuums Experts

Roger Potts

Level 3 Expert

694 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18299 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Fantom Vacums Vacuum Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...