Question about Computers & Internet

5 Answers

Need user manual for a Lanex/Verint netDVR. Also need the procedure to reset the netDvr to its default status. Thanks in advance for your assistance.

Posted by on

  • LUCY LYNN WILSON Jun 05, 2013

    HOW DO I GET THE SOFTWARE TO EVEN PROGRAM THE NET DVRII ? THE FRONT PANEL IS BASIC INFO, ONCE NETWORK I ASSUME THE SOFTWARE WILL SET YOU UP?? DO YO KNOW HOW TO GET SOFTWARE AND PROCEEDURES ON SETUP?

×

Ad

5 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Let me guess - you aquired a netDVR with no hard drive and put one in and it doesn't work. The hard drives are encoded with some data that is specific to Lanex, so you have to buy the hard drive from them at a large markup. This is my only pet peave with Lanex as otherwise they are one of the best on the market. Do you have the application to talk to the netDVR? If you do then the default password is 'admin'. this should let you in to make changes to the configuration.

Posted on Dec 06, 2010

  • 3 more comments 
  • bob8646 Mar 20, 2011

    I do have a netdvr-sd with two drive both have been wiped the manufacture no longer supports this model any idea where I could get a drive or the drive image ?

  • browningra Mar 20, 2011

    Were the drives totally wiped - i.e. does the netdvr recognize them or does it come up with a drive error? Do you have the DVR Control panel software. I know you can still get drives for them. Lanex encrypts an encoded string on the boot sector of their drives identifying it as a netdvr drive and the marks it up by a few hundred percent.

  • bob8646 Apr 04, 2011

    I do get a drive configuration error
    I have not been able to find a drive or a procedure to fix the old one
    If you have a contact or know of a way to get it fixed that would be great

  • bob8646 Apr 04, 2011

    I was just thinking that maybe one of the disk cloning software would copy the boot tract sector by sector

  • browningra Apr 04, 2011

    I've tried copying the sector but it didn't work I've got a stack of 5 NetDVR's that need hard drives and I guess I need to bite the bullet and buy some. The problem with that is the cost as they're fairly spendy.

×

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 103 Answers

Check this link

http://www.elongshi.com/UploadSoft/Manual_S3100_v3.30.pdf

A: Factory Default Configuration
74 Verint Video Solutions
The S3100 is programmed at the factory with the following
configuration:
Type Configuration
Access
management
?? User name: USERNAME
?? Password: PASSWORD
?? User accounts: Disabled
?? Telnet sessions: Enabled
?? IP firmware update: Enabled
?? Global security profile: Disabled
?? SSL passkey: <empty>
Network ?? DHCP configuration: Disabled
?? IP address: 169.254.*.* (MAC address of the
unit)
?? Subnet mask: 255.255.0.0
?? Gateway: 169.254.*.* (MAC address of the
unit)
Wireless
Communication
(North America)
?? Wireless passkey: ABCDEFGHIJKLMNOP
?? Frequency band: 802.11a (5 GHz OFDM)
?? Channel: Auto
?? Tx bit rate: Auto
?? Antenna gain: 13 dBi
?? Country: USA
?? Tx power scale: Maximum
Wireless
Communication
(Europe)
?? Wireless passkey: ABCDEFGHIJKLMNOP
?? Frequency band: 802.11a (5 GHz OFDM)
?? Channel: Auto
?? Tx bit rate: Auto
?? Antenna gain: 13 dBi
?? Country: United Kingdom
?? Tx power scale: 50% (-3 dB)
VSIP ?? VSIP Port: 5510
?? VSIP multicast IP address: 224.16.32.1
?? VSIP discovery IP address: 255.255.255.255

tell me if this works

Posted on May 02, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Whats the default password for the lanex net dvr? lost my manual

Posted on Sep 10, 2014

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I don't know if it works on the netDVR, but on the net DVR II you can follow the steps found here: http://therobinsonhouse.com/blog/?p=207 to reset it back to the factory defaults.

Hope it helps

Posted on May 24, 2012

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I do get a drive configuration error
I have not been able to find a drive or a procedure to fix the old one
If you have a contact or know of a way to get it fixed that would be great

Posted on Apr 04, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When i turn on my tv it tries to boot, blue mitsubishi home screen come up, i hear fan then it all shuts off while green light blinks.


Try a reset. Start by unplugging for 1 minute, then plug back in & if still won't restart try the following. If none of the following work, you will need a technician.

Initializing the TV in many cases can remedy a problem.
In the 2006 product line Initialization is now a user function.
Pressing the front panel "INPUT' and "FORMAT"
buttons at the same time activates Initialization. When
complete all user settings will have to be set again. The
table in Figure 4-3 list the User Initialization procedures.
Note: Pressing INPUT and FORMAT is the same as
the Initialization in the Option Menu (MENU-2-4-7-0)
Order Name Procedure Results Notes
1 System Reset Press <System Reset>
on Front Panel
Hardware & TV operating
software reset.
POWER/Timer LED flashes for 60
seconds. No customer settings
are changed.
2 User Initialization
Press <INPUT> &
<FORMAT> on Front
Panel at the same time.
All customer Audio &
Video settings are reset to
factory default.
All customer settings will need to
re-configured.
3 Reset System
Defaults
From the remote, press
<MENU> <1-2-3>
<ENTER>
All customer settings
except V-Chip are reset to
factory default.
Netcommand, Channel Memory,
etc., will need to be re-configured.
SERVICER
PROCEDURE 4 Initialization
From the remote, press
<MENU> <2-4-7-0>*
select "INITIAL" press
<ENTER>
All customer settings are
reset to factory default.
All customer settings will need to
re-configured.
MITSUBISHI RESET / INITIALIZATION CHART
CUSTOMER
PROCEDURES
Figure 4-3
Figure 4-4
LED Indications
The front panel LEDs, refer to Figure 4-4, also assist in
determining the cause of a symptom. Figure 4-5 illustrates
normal LED operation. Figure 4-6 shows the
LEDs response when a problem is detected and indicates
the possible cause.
Power/Timer
Indicator
Status
Indicator
Lamp
Indicator Condition
Off Off Off Off (standby)
Blinking green
fast Off Off Initialization (10 - 65 seconds)
Off Off Blinking
green fast Lamp runs for 1 min after PTV off
Green Off Off Power On
Blinking green Off Off Power On Timer is set
NORMAL LED INDICATIONS
Power LED Status LED Lamp LED Condition
High Temperature - check ventilation air flow.
(Temperature sensor is disconnected.)
Off Off Blinking yellow Lamp cover is open.
Lamp failure (Lamp fails to turn on)
Off Off Red (Lamp turns off after lighting)
Lamp is broken
Off Blinking Red Off Fan Stop
Off Red. Off Circuit failure. (Run Error Code Check)

Apr 08, 2015 | Mitsubishi WD-65731 65-Inch 1080p DLP HDTV

1 Answer

Frigidaire refrigerator filter status light is red


That information is in the user manual that covers your model number. Below is the procedure for a Side by Side. To look for your manual click=> HERE
Press and hold the Water Filter button
on the Ice & Water Dispenser control
panel for three seconds. When the display
changes from "Red" to "Green," the status
has been reset.

I am here should you need me, Thanks John Tripp Appliance 911
Contact Me Here

Mar 17, 2014 | KitchenAid KSBP25FKSS Side by Side...

1 Answer

Change navman my55t pin code.


I tried to download the user manual for your model, but unfortunately the server link was dead (this may be temporary). Try going to Navman Support for either another try at the manual's download page or an e-mail link for the answer to your question.
Some equipment has a "reset to factory default" button or procedure; this should reset the PIN and user settings to factory default. I don't know if this is the case with your GPS unit since I can't get the manual, but this would be the simplest method if it doesn't erase map updates.

Jul 19, 2013 | GPS

2 Answers

Zmoda "no root"


You will need to contact Zmodo. It is most likely a corrupt password. You maybe able to access your menu, but wont be able to do anything and will get the "no root" error message. They will verify you are the actual owner via either your registration or a number off your orig invoice, for security reasons. (You could be a crook trying to delete the evidence, its good they check) They will then give you a bypass admin code to put in, then direct you to change your password and you should be all set. I just got done doing this after waiting for an hr with their online LIVE chat, and finally just called and waited the 15 mins for someone to answer. Its a small shop, but, they were friendly, knowledgeable and most important, spoke REAL ENGLISH!! =]) I spoke with Tony and after I got it fixed, he gave me a case number which will allow me not to have to go through all the verification next time around if I give it to him.. so, find your invoice and place that case number on it for future reference and put it in a handy location you wont forget.
Hope this helps the 20 plus ppl I found also asking pretty much the same question. I looked all over the net and I am an IT Professional and I couldn't find an answer.. even on their website. I plan on adding the answer there too as well. Have a GREAT DAY! =])

Jan 08, 2013 | OEM Systems Zmodo Surveillance...

2 Answers

I could access the router log in page and then go to the status page but I cannot go to the advanced setup page. I would like to know the setup page address that should be like...


For user access enter the default user password user to view the status only. The
following window will appear.

Administrator Access

1 For administrator access enter the default admin password 1234 to configure the wizards
and the advanced features.
2 Click Login to proceed to a screen asking you to change your password or click Cancel
to revert to the default password.
3 If you entered the admin password, it is highly recommended you change the default
admin password! Enter a new password between 1 and 30 characters, retype it to
confirm and click Apply. Alternatively click Ignore to proceed to the main menu if you
do not want to change the password now.

This router has a user password to see the status and an administrator password to change settings. Please mark this as solved if this solves your problem. If not feel free to ask more questions :).

Mar 02, 2011 | Zyxel P660HW-D1 Router

1 Answer

I need to change the ip address of my sharp ARM276 network printer and I don't know the user name and password. I need to reset the username and password to their defaults to login. Can someone help with...


You can't reset password, but you can see admin PIN on printer's display.
Just use simulation 22-7.
You can read about simulations in "service manual".

Jun 24, 2010 | Office Equipment & Supplies

1 Answer

Need to reset it.


D-Link Router reset
Step 1 Locate the reset pinhole on the back of the unit.
Step 2 With the unit powered on, press and hold the Reset button.
Step 3 Hold the Reset button for about 10 seconds.
Step 4 Release the Reset button.
Step 5 The unit will reboot. Allow 20-30 seconds before reconnecting.
Step 6 The device is now at factory defaults.
Note: Do not recycle power during the reset procedure. The default user name for most D-Link devices is admin and the password is left blank.
When it says hold for about 10 seconds, don't hold for more than ten seconds or the procedure will likely fail, if ten seconds doesn't work try 5 seconds.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe

May 16, 2009 | D-Link AirPlus Xtreme G DI-624 Wireless...

1 Answer

Fuser Assembly damaged by user trying to remove paper jam.


This is one of those that is not quite so easy. I have uploaded the service manual for you. You may download it here.

Thanks and please take a moment to rate this solution as fixya as I have taken the time to upload the manual for you. Good luck!

Feb 14, 2009 | HP LaserJet P2015dn Printer

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

3,948 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

kakima

Level 3 Expert

102366 Answers

David Payne
David Payne

Level 3 Expert

14161 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...