Question about 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

1 Answer

I have 2 viper 5701 alarms and want to program them both to 1 controler and can't figure out how to do this can you help

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Como porgramar el control?

Posted on May 04, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

REMOTE USAGE


They probably don't do anything. They could be programmed to pop the trunk or roll the windows down or something but not always used.

Jan 17, 2014 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

1 Answer

Viper 5701 led light does not flash when armed, stays lit when alarm is disarmed


If the LED is on solid then the alarm is in valet. To exit valet, press "F" twice then press unlock on the remote. The LED should turn off.
OR,
enter the vehicle, turn the ignition on then off, press and release the valet/programming button on the antenna. LED should turn off

Jan 30, 2013 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

1 Answer

I am trying to disarm the viper 5701 2 way alarm w/ remote start and the keypad nor is the manual override responding. How can I disable the alarm?


Get in car........alarm will be going offVisually find the black valet button..........it should be next to led on the antennaTurn key to IGN position...........so all dash lights are onWithin 5 seconds push the valet button 1 time..............may have been programmed to more times, but ussually notSiren should stop and you can start the car.
TO put into valet mode
Key to IGNKey to OFFPush valet button 1 time.Led should now be solid.

Jul 09, 2011 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

1 Answer

Hi. I have a Viper 5701 alarm in my car. Arm and disarm goes very well with the control unit. But I cannot programming to pasive arming, always have to use de button in remote control to works. Is ther a...


Open door, turn ignition on then off. Press aand hold programming button until you hear one chirp. After you hear the chirp, release programming button, press and release button one then press and hold. You will hear one chirp. While holding the programming button, press lock button on remote to change option. One chirp is active arming(what you currently have), Two chirps is passive arming without locks, Three chirps is passive arming with locks. Turn ignition on to exit programming. Test system.

Jun 13, 2011 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

1 Answer

I have a viper starter and car alarm with 2 controlls and one got stolen what should I do


The Viper alarms will accept (if I remember correctly), 4 codes at one time. That is, 4 individual remotes, or two remotes two times, or one remote 4 times. So, if you program your remote 4 times, it will essentially remove any previously programmed remotes. Another option, and you'll have to check with your dealer, but I think there is a way to delete ALL remotes, and then program your remaining remote one time, and again, all previously programmed remotes are now removed from memory. This was done by the manufacturer just for such events.

May 17, 2009 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

1 Answer

Viper alarm keypad will beep for 30 seconds every time I arm or disarm


Change the battery, 2-way remotes require 2 slim batteries on top of one another. Regular remotes only require 1.

May 10, 2009 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

2 Answers

Viper 5701 remote


read the owners guide look at page 11 remote control programing you have to follow the instructions after your in the programing mode go to page 12 look at the unlock symbol and finish the programing

Dec 21, 2008 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

Not finding what you are looking for?
5701 VIPER 5701 2-WAY ALARM w/REMOTE START Logo

Related Topics:

335 people viewed this question

Ask a Question

Usually answered in minutes!

Top Viper Vehicle Parts & Accessories Experts

Kevin Daniels

Level 3 Expert

1455 Answers

Tre Elkins

Level 3 Expert

643 Answers

Shehu Pro
Shehu Pro

Level 3 Expert

1284 Answers

Are you a Viper Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...