Question about Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher

1 Answer

Timer stops count down at 1 minute remaining. Dishwasher continues to run.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Bosch Master
  • 2,605 Answers

Hello,

The reason your dishwasher is displaying a "1" is the control has detected a heating error. Here`s why...

The issue with your Bosch dishwasher likely lye`s within`the electronic timer/control, specifically the heater relay solder joint. ( a faulty flow switch, ntc or heater can also cause this, but not very probable ). This is why it runs forever unless pressing the two buttons for "cancel".

To repair your unit It will require you to remove the control from the unit and then remove the control from it`s plastic housing and look for a burnt solder contact on the printed circuit board. This will be one of the pins from the heater relay, hence the unit sit`s at "1" ( because it can`t heat to advance or until canceled ) trying to heat the water.

**Further to this, if you or someone you know is proficient at soldering, a lot of times it can be remedied by simply repairing the solder...although Bosch recommend`s replacing the control and I don`t pretend to speak on there behalf nor do I profess to know better. This is just my experience (it work`s) and my opinion (why buy new if one can repair ?)**

**Please disconnect the power before attempting any service to the dishwasher. If you do not feel comfortable attempting this service, call a local pro, preferably one familiar with Bosch/Thermador/Gaggenau, to service your machine.**

Hope this answer`s your question's, let me know if I can assist you further. Thank`s for visiting "fixya" for your repair inquiries. Please take a moment and rate this solution to it's helpfulness to you and leave a testimony if you're satisfied.

Good luck.

macmarkus :)

Posted on May 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Descaling process counts down on the displat but no solution is running through the unit and thr counter stops on 1 min remaining


This is normal behavior, your machine is fine.
For example, the machine says "5 minutes remaining" and then it goes 5:00, 4:59, 4:58....etc all the way down to 4:01.Then it changes to "4 minutes remaining". Which is 4:00, 3:59, 3:58, etc.
So at "1 minute remaining" the machine is really at 1:00, then 0:59, then 0:58 and all the way down to 0:01.So, after the "1 minute remaining" goes away, the machine is actually done cleaning itself.

May 08, 2011 | Miele CVA 4066 Stainless Steel

1 Answer

Compressor UP6 25 125, runs all the time but is only under load for a short time, should it shut down between loads?


This unit will shut down if unloaded for a set period of time. Usually 5 to 10 minutes. This time could be longer if some one has changed it from the factory setting. There is a timer in the control box that starts counting down when the unit unloads. If it stays unloaded long enough for the timer to count down the unit will stop until the air pressure drops to the low set point on the pressure switch. It will then start up. If the unit loads before the counter counts down the timer starts from the beginning when it unloads again. This cycle continues until you manually shut it down or you stop using air long enough for the timer to reach Zero and shut down.

Apr 22, 2011 | Ingersoll Rand UP6-25-125 120 Gallon...

1 Answer

My dryer timer counts down to 7 minutes and then continues drying


replace the sensa board and make sure the wires on the sensors are ok

Jun 07, 2010 | Whirlpool GEW9250 Electric Dryer

1 Answer

We have a Bosch dishwasher model SHU5315UC/U06. When we ran a "Regular Wash" the dishwasher ran continuously and the timer did not count-down. None of the Delicate or Rinse and Hold buttons responded. ...


My father-in-law has a Bosch and they had the same problem. The tech guy said it was not heating properly and that caused it to continously run because it won't tick down the timer if it doesn't reach a certain temp, so try turning your faucet as hot as you can, right before you turn on the dishwasher and see if that is the problem, if not the heating element might not be working properly. If you still have a warranty, try to get them to see and fix it, otherwise, get a repairman to check it out. You can also turn up your hot water heater, but not so hot it would be dangerous to use, but enough to get the temp up. Otherwise the heating element might need to be replaced.

Jul 28, 2009 | Dishwashers

1 Answer

Dishwasher will not run through its cycle


Hi

If the cycle doesn't complete, check these:

Water-heating cycle Many dishwashers heat the wash and/or rinse water to a higher temperature, as the cycle calls for it. In these cycles, the dishwasher pauses after it has filled with water, waiting for the water to reach the pre-set temperature. What happens next, depends, as follows:

  • On some units, the pause is timed and the unit continues after the allotted time.

  • On others, the cycle can't continue until the water reaches the higher temperature. If you have this type of dishwasher and the water isn't being heated (say, because of a problem with the heating element or thermostat), after the unit stops at the heating cycle, it never continues. When you repair the heating-system problem, the "cycle problem" is fixed too.

Timer Timers don't often fail. But if every other part of the dishwasher seems to be working properly and the timer knob seems to be stuck in one place--doing one function continuously--the timer may be at fault. Dishwasher timers can't be repaired. If yours is defective, replace it.


Please revert for further assistance and Do rate the solution as "FixYa" if found useful.

Thanks
Rylee

Mar 26, 2009 | Dishwashers

1 Answer

Washer keeps spinning water and not moving on to the next cycle


Sounds like the timer has gone bad and is not letting anything work. Washers, dryers and dishwashers have a timer that you set at the start and then the system counts down off of that. If that stops working it will run forever

Feb 12, 2009 | Bosch 24 in. SHU43 Built-in Dishwasher

2 Answers

MDB7100AWB STOPS AFTER 3 SECONDS OF RUNNING


1. The Maytag sevice centers, if close, are "great". You describe the problem and they supply the part. If far still give them a call.

2. The problem is probably the control. It's a simple fix. Just replace the part. And you can order the part from the service center. Takes 10 minutes.

Tango

Feb 09, 2008 | Maytag MDB7100AWB Dishwasher

2 Answers

Hoover Whisper HD97E


Try checking the water level, and level switch? Is the outlet hose high enough of the floor? If you tip the machine back you should see one or two clear plastic tubes, take one end of these and blow through them and the do it the other way round.

Nov 26, 2007 | Hoover 24 in. DT999 Free-Standing...

2 Answers

Electronic controls don't count down properly


you have to replaced the main control resoldering wont fix it because the relay itself has gone bad replacing the board will solve the problem

Nov 20, 2007 | Bosch SHU5315UC Dishwasher

Not finding what you are looking for?
Bosch 24 in. SHE44C02UC / SHE44C06UC / SHE44C07UC Built-in Dishwasher Logo

426 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Dishwashers Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18389 Answers

shaun taylor

Level 3 Expert

1525 Answers

Are you a Bosch Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...