Question about HP Media Center m7250n (ED842AA) PC Desktop

1 Answer

HP PC m7250n- fan always on high speed - HP Media Center m7250n (ED842AA) PC Desktop

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Question = are u over clocking ? and /or is your processor fan and fins dirty causing over heating causing the fan to run on high trying to cool down a heated/overheated processor.

Posted on May 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fan runs hard computer is slow hp compaq nc6000


- Stop Overclocking your CPU.
- Make sure your Heat Sink is placed properly above the processor.
- Clean the Processor fan, Heat Sink and other peripherals.
- Use High Speed fans.
- Use CPU Heat Sink Paste in the processor.
- Fix OS registry with reliable program like I always use Reginout.
- Shut down your computer at least two hour a day.

Hope these tips will help.

Jan 05, 2014 | HP Compaq 6735s Notebook

1 Answer

HP m7250n shuts down unexpectedly.


your power supply is faulty you will need to replace it. If you recently installed a new hardware it could be you don't have enough power to, either upgrade you power supply or remove the hardware.

Feb 27, 2010 | HP Media Center m7250n (ED842AA) PC...

1 Answer

57.03 error shows in hp p 3005n laserprinter


.03 identifies it as a right fan error. The suggested remedy for this error is to replace the DC Controller board. Contact HP for replacement information.

Good Luck,

NOLA Tech

Jan 29, 2010 | HP Media Center m7250n (ED842AA) PC...

1 Answer

57.03 error


57.x FAN FAILURE CALL SERVICE Control Panel Message 57.x FAN FAILURE CALL SERVICE Event Log Error Service Messages: 57.01.00 57.02.00 57.03.00 57.04.00 Required Action
  1. A fan motor failure occurred. All fans are enabled to low speed operation at printer power-on. Fans will go into high-speed operation during the print cycle. All fans are disabled during PowerSave Mode.
    • x = 1: FM1 (Laser/Scanner Fan)
    • x = 2: FM2 (Power Supply Cooling Fan)
    • x = 3: FM3 (Formatter Fan)
    • x = 4: FM4 (Face Down Deliver Fan)
  2. Cycle power. It the message continues, check and reseat cabling between the fan motor(s) and the DC Controller PCA.
    • Fan 1 J208
    • Fan 2 J216
    • Fan 3 J210
    • Fan 4 J225
  3. Replace the faulty fan motor.

Aug 20, 2009 | HP Media Center m7250n (ED842AA) PC...

3 Answers

CPU FAN SPEED IN HP Compaq d530 Small Form Factor Desktop PC


The fan/heat sink on these models get plugged with dust very easily, use an air compressor or can of air to blow the dust out of the heat sink and fan. In extreme cases the thermal paste gets dried out and needs to be re-applied to properly cool the processor.

Dec 01, 2008 | HP Compaq d530 SFF PC Desktop

1 Answer

HP Media Center PC m7250n will not power up


hold the start button in and check the back of the case to see if the power supply fan turns while the power button is depressed. If it turns while the button is pushed, but then stops when you let off the button, then the power supply is probably bad and needs replacing.

Jun 01, 2008 | HP Media Center m7250n (ED842AA) PC...

2 Answers

Hi there


Cilck this Link:

This will open the driver selection page.
Select your Operating System, download all required drivers...and finally..... :))

Thanks
Iqbal

Apr 03, 2008 | HP Media Center m7250n (ED842AA) PC...

1 Answer

Stopped booting


power supply fuse maybe trip/busted, you let repair the PSU to repair shop or you replace it with the same wattage rating or higher.

Jan 13, 2008 | HP Media Center m7250n (ED842AA) PC...

Not finding what you are looking for?
HP Media Center m7250n (ED842AA) PC Desktop Logo

Related Topics:

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18408 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a HP Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...