Question about Panasonic PT-50LC13 50" Rear Projection HDTV

1 Answer

I replaced the lamp but the power button is flashing green

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Panasonic Master
  • 14,553 Answers

This is a model which was part of a rather large class action lawsuit a few years ago. Most were if original owner exchanged for a new model.

Many had problems where the lamp would repeatedly fail. I know as the shop I work for was involved in the exchange program and we would pick up the old set (problem or not) and deliver a newer model to the customer.

We did Panasonic authorized repairs and they did want the old sets back but told us to take anything out of them we wanted as they were just going to scrap whatever got returned to them.

The most common failure in these sets was the Ballast which is really the power supply that fires the lamp up went bad. At one point in time they completely ran out of replacements and had a "kit" where the supply had to be removed and several parts in it replaced out of hand.

I did this several times in people's homes. A newer replacement Ballast eventually arrived but it is pricey and not a do it your self job to get at, remove and replace.

For your information my recent research shows:

Manufacturer Panasonic Part Number LSEB3087A Description PC BOARD List $160.25 Your price $127.38 Core charge $250.00The board in a metal box is sold on exchange basis as they really do not want to have to continue producing parts for this model.


Some of the sets we picked up actually worked fine but by then the word was out.

Let me know if you have questions or need advice as I am here to help you.


Regards, SD TECH


Posted on May 01, 2010

  • directmatche
    directmatche Mar 12, 2012

    I have a PT-50LC13 and I bought a ballast repair kit. I am having problems taking the board out. I can't seem to remove the board because those plastic clips wont come off and also a couple of connections won't come off either. How do I get these off?

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trying to replace lamp in HDTV and having trouble. Does not function correctly after putting in new bulb. Boots up and then visuals go black and the green power light keeps flashing. Help?


Panasonic DLP TV Bulbs

Make sure its an original Osram or Philips bulb inside the housing. If its a cheap lamp it will act this way. If it is an original lamp, then you may have a power supply issue. It shouldn't affect your TV but you may want to try resetting the lamp timer by following the instructions that came with the lamp.

TY-LA1001 Timer reset

While pressing the VOL- button on the projection display, hold down the number 0 button on the remote control at the same time for more than 5 seconds.

Aug 15, 2015 | Panasonic Pt-52lcx16 Projection Television

1 Answer

No power to tv. When i press the power button i only get a blinking green light then it stops and the blinking red light for lamp flashes and keeps flashing


You need to replace your lamp. Also check power supply and ballast board. Most of the time if you replace the lamp it will come back up. After replacing the lamp you will need original remote to reset lamp hours.

Jan 24, 2011 | Sony KDS55A2000 55" HDTV

2 Answers

Suddenly turned off without warning Sony KDS-50A2000


Hello,

All you need is to open the back cover of the television and check on for dry soldering at the power stage of the printed circuit board, also check for bulged capacitors, if found replace with same rating of voltages , but if otherwise Ur power supply board is dead, u know basic electronics’ and soldering? Most of the times, the power supply board just have dead leakages gases capacitors.These capacitors always bulges up on it top,or puff up on it top.Replaced these gases leakages capacitors will get ur tv power stable,and work again.Or tries websites like Shopjimmy.com,Ebay.com to buy a whole refurbish power supply board for the replacement.

Hope this helout, Good luck....

Jul 11, 2010 | Sony KDS-50A2000 50" HDTV

2 Answers

Just replaced lamp. when plugged in, power light


hello make sure the lamp is fitted securely and the lamp cover aswell

regards
shaun

Jan 16, 2010 | Panasonic PT-50LC13 50" Rear Projection...

1 Answer

No picture, no sound, power button blinks 47 times, then lamp flashes 134 times, then shuts off


It is symptom of weak Lamp in your TV, replace Lamp with following part number..
A1606034B LAMP BLOCK XL-2100U
It is available in Sony Accessories for $200
Always buy Sony Original Lamp for your Sony TV and avoid aftermarket/ cheap lamps.

Apr 22, 2009 | Televison & Video

1 Answer

Panasonic PT L501u Replacement Lamp


panasonic projectors , even if the lamp has reached end of life gives u 10 minutes to reset the lamp counter
so when u replace a new lamp, go to options, lamp counter, reset & press stanby button for confirmation!
thats all the unit powers off & when u check the lamp counter , its shows 0
u r done!!!!!!

Jan 22, 2009 | Panasonic PT L501U Multimedia Projector

1 Answer

No lamp


whats your location, The power supply is faulty, but fairly easily repaired, if you send it to me, I will sort it out

Feb 13, 2008 | Hitachi CP-X327 Multimedia Projector

5 Answers

Won't power up


I had the same problem after I replaced my lamp. You need to hold down the:

On
Enter
Down Arrow
Right Arrow

simultaneously - this resets the lamp counter. After I did that my projector fired right back up.

Nov 22, 2007 | SharpVision XV-Z9000U Multimedia Projector

Not finding what you are looking for?
Panasonic PT-50LC13 50" Rear Projection HDTV Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Televison & Video Experts

 Grubhead
Grubhead

Level 3 Expert

5158 Answers

The Knight
The Knight

Level 3 Expert

74383 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Panasonic Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...