Question about Amana ACD106R Wall/Window Air Conditioner

Open Question

Amana ACD106R 10,200 BTU 110V window unit - E1 error code

When the power went out last week, came back on in about 2 or 3 minutes, I now have an error code "E1" in display, and nothing works. I have reset power cord switch, as I was not getting a reading at all until then. Anyone know the codes for my Amana ACD106R 10,200 BTU 110V window unit? It's been a great A/C and haven't had any problems before this.

Posted by on

  • jimmyc2 Apr 30, 2010

    Thank you for your response, Ladyybug68. I have tried that. As a matter of fact, I left it unplugged for an hour or so, but it comes back with the same code. I was hoping that it would reset the board, but no such luck. :-) I have found the board online (including the LED and control board) for $41.+, but wanted to make sure that the boards were bad b4 I replaced them. There is also a fuse on the back board, and I checked it with OHM meter, and it was good. The only thing I can see that would cause this would be the boards, as that is all that is there except for the capacitors. Thank you for your help!
    Jimmy

  • laura Newman May 11, 2010

    Have you tried to pull the power cord and wait approx 10 minutes before plugging it back in? ....It might reset the control board. :-)

×

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: Beeping Noise

when the air conditioning aircon is have niose get a more prion in the copper tube and you will see the effect

Posted on Jun 22, 2007

Ad
  • 3600 Answers

SOURCE: I have a 15,000 BTU A/C unit 110v through the

take it back and get a replacement, sounds like it had a hydrolic action on the pump and blew the pump so get it replaced at no cost to you. It happens.

Posted on Jul 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Haier service manual


This is what you error code means.
E1 = Room temperature sensor fault
Haier Air Conditioner Fault Codes


AC Repair Tamarac

Aug 25, 2014 | Haier Esax3186 Energy Star 17,000 Btu...

3 Answers

E1 error code displays when unit is plugged in I have a wall unit with about 10,000 BTU capacity. Two days ago, it quit working and displayed the E1 error code. I unplugged the unit, let it sit for 10...


highly annoying issue error code E1. After hours
of fan operation, the error code E1 will appear on the seven segment
LED temperature display. This error code is intended as a reminder for
the user to clean the air filter. However, because the procedure
outlined in the user manual does not clear this error code as
indicated, and the appliance has a nonvolatile memory that cannot be
reset by simply unplugging it, the user of the appliance will become
mightily frustrated, standing in potentially sweltering heat watching
the appliance repeatedly shut down in the midst of operation with the
"E1" display flashing.

Believe it or not, that is what it does: if you unplug it to remove the
"E1" code from the display, and plug it back in and re-start it, it
will simply run for anywhere from a few minutes to a few hours, and
then merrily shut down again with the same flashing "E1" code.

So you will come home to a hot bedroom, living room, etc. unexpectedly,
and you will NOT be amused, as I was not.

Many people at this point, having put the manual under the canary or
some such, will simply return the unit and never buy another Sharp air
conditioner. But for the tech-savvy and search-adept, I offer the
following procedure to clear the nefarious E1 indication, and obtain

1. Power down the air conditioner using the "power" button on the front
panel.
2. Unplug the air conditioner from the wall socket.
3. Hold the front panel "power" button down and plug the air
conditioner in. Continue to hold the power button down as the machine
goes through a brief test sequence (fan & compressor each come on
briefly, etc). There is a "beep" sound at the end of the test sequence,
and the machine will be off. At this point, you can release the power
button.
4. Unplug the air conditioner.
5. Plug the air conditioner back in.
6. Congratulations! You should now be able to operate the air
conditioner normally for another 720 hours, but only if you followed
the instructions above EXACTLY.
_____________________________________________________
Was this solution helpful? Show your Appreciation by rating it.
Thanks for using fixya support..You have a wonderful day

Jun 05, 2008 | Haier hwr10xc6 Air Conditioner

1 Answer

E1 error code LFWC38F6LS


Good Morning Chris,

I see that you are receiving an E1 error code on your wine cooler, model# LFWC38F6LS, even though your wine cooler is still working. This could possibly be a false error code, caused by a miscommunication between the different control boards inside your appliance. I suggest resetting it by either unplugging it or cutting the power at the circuit breaker for 2-3 minutes. If when you bring power back to your wine cooler, you are still receiving the E1 error code, I suggest contacting either the manufacturer or your local authorized technician. Hope this is helpful.

-Best Regards-
WP

Mar 18, 2014 | Frigidaire 38-Bottle Two-Temperature Zone...

1 Answer

I have a fitness Edge 491 Recumbent bike that the display window reads E1 . the resistance is hard and I am unable to reset. when I press start stop for 2 seconds it all looks like it will reset but then...


The bike is no longer sold and the company went bankrupt in 2014, so neither support nor parts are available from the company. Try the results of this Google search regarding the E1 error code:
fitness quest edge 491 e1 error Google Search

Nov 25, 2017 | Cycling

2 Answers

Getting an E1 error message..wont start


Hi,
1. Unplug unit. 2. Hold down power button while plugging in unit. It will do a short self-test and then beep. leaving unit off. 3. Release power button and unplug. 4. Plug in again and turn on normally. This should last for about 720 hours, at which point the E1 error will come back and you need to follow the procedure again. (You might as well clean the air filter at this point just in case it really needed it...)
Let me know,if needed further assistance.
Hope i helped you.
Thanks for using ' Fixya ' and have a nice day!!

Sep 03, 2011 | Amana ACD106R Wall/Window Air Conditioner

5 Answers

What does the error code F1 E1 mean and how can i fix it


Hi.

F1 - E1 means: EEPROM Checksum error. The EEPROM is a memory chip located in the ERC (control module). The problem is communication error with the EEPROM


1. Disconnect power for at least 30 seconds.
2. Re-apply power and observe for at least one minute.
3. If code re-appears, replace control board (also called ERC or clock).

Note: Applies to all F1-Ex codes except F1-E3.

Regards.

Ginko

Aug 29, 2011 | Whirlpool 30" Self-Cleaning Freestanding...

1 Answer

Unable to use the oven since the power outage...two codes appear on the display--e1 f1......tried to reset but no luck.


Hi

Error code F1-E1 means that an error with the keypad has occurred. Usually it happens due to loose ribbon cable on the keypad or the electronic control assembly itself going bad. To resolve this issue first, disconnect the power to unit and then gain access to the back of the clock assembly (Electronic Range Control/ERC). Now unplug the touch pad ribbon connector from the ERC, it would be a flat wire approx. 1 1/2" to 2" wide and make sure that the cable is not broken and nothing is shorted on the keypad. After this is done insert the cable back and then plug the unit back to check. If the error is still there then the electronic control board should be replaced. Hope this helps...please post back for further assistance.

Daniel

Jul 25, 2011 | Kenmore 79012 / 79014 / 79019 Gas Kitchen...

3 Answers

My unit shut off now displays E1.


Sharp updated the procedure for resetting the E1 code.

1. unplug unit
2. hold the Power button while plugging the unit back in
3. keep holding the Power button until the unit beeps
4. unplug unit again
5. plug it back in and it should be good

Here is the updated user manual

http://www.sharpusa.com/downloads/archives/product_manuals/air_man_AFS100FX_S120FX_S125FX_R100FX_R120FX.pdf

Jun 05, 2010 | Sharp AF-S120FX Air Conditioner

Not finding what you are looking for?
Amana ACD106R Wall/Window Air Conditioner Logo

Related Topics:

718 people viewed this question

Ask a Question

Usually answered in minutes!

Top Amana Heating & Cooling Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Bill Long

Level 3 Expert

588 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you an Amana Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...