Question about Zebra Printer 140-751-00000

1 Answer

My printer says error condition paper out. But it

My Zebra Z4m printer says error condition paper out. But it has paper

Posted by on

  • Bob Miller May 11, 2010

    Need a little more info. Did this happen when you put a new roll of labes on that are the same size or different size from before ?

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

  • Zebra Expert
  • 285 Answers

Try to recalibrate media and sensors, run calibration, and run sensor profile, save, and restar again the printer. check if setings from the driver are correct or they can change the setings from the printer

Posted on Nov 13, 2010

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Technician can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Technician (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 17 Answers

SOURCE: Zebra Z4M Printer error condition p3/p5

defective printer head

Posted on Mar 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Zebra Z4M printer error


Hi,

Did you try disconnecting it from the power for a few hours?

Mar 17, 2008 | Zebra Z4M Printer

1 Answer

I turn on the zebra z4m and it runs the labels even with no information sent to the printer. I can not use the cancel or pause button to stop. I runs for a minute and then error condition ribbon out. I...


1.Double check that the ribbon and the labels are routed correctly. 2.Make sure the media guide is holding the labels against the inside of the printer and not moving to the right away from the media sensor. If the labels are sliding to the right as they come out, increase the left side head pressure on top with a flat blade screw driver. Download the user manual at zebra.com .Check the media type and sensor type, and set for thermal transfer if using a ribbon.

Feb 24, 2011 | Zebra Z4M Printer

1 Answer

I have a Zebra Z4M printer. We use it to print on various labels - pre-printed and blank labels (semi-gloss). I've been struggling to print on one of the pre-printed labels. Everything else prints...


some labels are hard to calibrate, nee to calibrate the sensors with manual calibration.
1} go to the MEDIA AND RIBBON CALIBRATION,
2}take 2 or 3 labels from the base paber, load the way to the based paper stay unther the sensors, 3}close printhead.
4} press ok.
5} Move the ribbon out from sensors and close the printhead.
6) press ok
7) wen printer ask RELOAD ALL, load the labels correcly and the ribbon, close the printhead and the top door, and press ok. The printer run the calibration it self.
wen finish, saved (press setub twice) and test.

Jan 21, 2011 | Zebra Z4M Printer

1 Answer

Zebra Z4M only feeds a small portion of the label.


You should try a factory reset. Power off the printer. Hold the "pause" and "feed" buttons down while powering up. Allthe lights will blink and when they stop blinking, release the "pause" and "feed" buttons. This will factory reset the printer.

Apr 24, 2009 | Zebra Z4M Printer

1 Answer

Z4m zebra printer problem


Might foul the ribbon sensor, clean the sensor and try to print again.

Mar 02, 2009 | Zebra Z6M Plus Thermal Label Printer

1 Answer

Zebra 4M printer stopping due to error message


The printer is dirty sensor label or no label is calibrated. Turn off the printer and press FEED, CANCEL, PAUSE and turn on, release the keys to advancing the label, and let print be calibrated. Roberto Martinez Mexico bartech9@yahoo.com.mx

Feb 26, 2009 | Zebra Z4M Printer

1 Answer

ZEBRA Z4M LABEL PRINTER LOCKED UP


The printer is Z4M or Z4M plus? I found this error at z4m plus and the solution is to change the motherboard. Roberto Martinez Mexico bartech9@yahoo.com.mx

Nov 14, 2008 | Zebra Z4M Printer

2 Answers

Zebra Z4M printer error


The mainboard does not need to be replaced, just the sensor head open is dirty and needs cleaned.

Mar 10, 2008 | Zebra Z4M Printer

Not finding what you are looking for?
Zebra Printer 140-751-00000 Logo

1,563 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zebra Office Equipment & Supplies Experts

Dave Busselle

Level 1 Expert

54 Answers

yadayada
yadayada

Level 3 Expert

77499 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Zebra Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...