Question about Jandy AQUALINK RS TELELINK KIT

1 Answer

My aqualink RS8 is reading 6700 REV C in the display window and ALL of the display lights are flashing on. I have tried the reset button and pushed the menu and cancell buttons. Nothing seems to work. How do I clear this so I can control my pool

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jandy Master
  • 4,292 Answers

Check wires to aqualink 4 pin connector wires touching cut wire if all ok need new display

Posted on Jan 30, 2016

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

CNC65
  • 15 Answers

SOURCE: Jandy Aqualink - Rs, button control red lites on contriol panel

HAVE YOU HAD ANY LIGHTNING STRIKES?

Posted on Nov 06, 2008

PartsCenter
  • 125 Answers

SOURCE: Operating instructions for Aqualink RS8 pool/spa combo panel?

AQUALINK GUIDE

Posted on Feb 26, 2009

  • 1 Answer

SOURCE: Why am I getting a 6700 REV C message on my AquaLink RS6 home spa

I had the same issue, but only after I pressed the reset button on the side of the panel. After a couple of days of troubleshooting, I found a small nick in the wiring from the outdoor unit to the indoor paneI. I turned off the breakers to the pool equipment, rerouted a new cat5 cable, but cat3 will work just as well, wired it up and all was good. A local pool guy wanted to charge me about $2000 to replace both units. I spent less than $5.

Good luck

Posted on May 28, 2009

  • 990 Answers

SOURCE: Jandy aqualink rs8.Pool and spa lights wont come

If it's both lights and they are on seperate switches I would start by checking the GFCI and be sure it is not tripped and if it is you would need to find out why. Then check power in and out of the light module in your power center. If you can set the power center to service and turn the lights on manuley from there then it is programming but most of the time it will be something in the lights or their circut.

Posted on Mar 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Blue haven bh6100


wire to the house controller has been cut or plugs at aqualink or controller wires touching if all ok then check controller at aqualink with cheater cord cut some off wiring on inside of cover if still doesn't work bad bezel board

Jun 20, 2012 | Jandy AQUALINK RS TELELINK KIT

1 Answer

I have an aqualink RS8, which controls the on/off timing of the pool/spa, fountain feature, solar heater and yard lights. 1 - the display reads "6520 rev hh" 2 - the spa has been turning on by...


first disconnect the spa side remote if they go away replace the spa side remote if they don't go away go to system setup and go to programs either cancel if all button or delete or edit if one touch or PDA

May 25, 2011 | Jandy Aqualink Rs4 One Touch Control...

2 Answers

On Jandy Aqualink RS display it says 6700 Rev C and all the display buttons are lit so we can't control anything What do we do?


This sounds like a boot stall (program freezes on start-up)
First things first, turn off all power to the unit and everything it is interfacing with.
If this is not a boot stall, then it is possible somebody has entered a programming mode and it is frozen there. Try reboot here as well.

If this does not help, more info is needed, such as. What was the most recent activity having to do with this equipment. was there water splashed on this device? were there any recent modifications to the device.

If you need more information, you may contact me @: adamh@newconceptchem.com

if this post helped you, please take the time to vote positively for me on this site.
thanks,
adam

Oct 28, 2010 | Jandy AquaLink RS OneTouch RS8 Pool or Spa...

2 Answers

Control panel has burnt out motherboard.. nothing works


nope sorry it will not be cheat to replace but must be replace if you want to have full automation

Jul 02, 2009 | Jandy Aqualink Rs4 One Touch Control...

1 Answer

Aqualink RS6 all lights on control panel lit and won't work


I' m having the exact same problem, where the panel lights up and is non-responsive. Did you ever find a solution?

May 21, 2009 | Jandy Aqualink - Rs24 One Touch Pool / Spa...

2 Answers

Operating instructions for Aqualink RS8 pool/spa combo panel?


To clear the memory
Push the menu button once
Push the back arrow to "System setup"
Push star * or enter button
Push back arrow till display says " clear memory "
Push star or enter
Push star or enter again to confirm.
You will get a message "erasing memory"
Now you can reprogram system

Nov 18, 2008 | Jandy Aqualink - Rs24 One Touch Pool / Spa...

Not finding what you are looking for?
Jandy AQUALINK RS TELELINK KIT  Logo

Related Topics:

287 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jandy Pool & Spa Experts

David Spradling
David Spradling

Level 3 Expert

4292 Answers

Pj Kiley
Pj Kiley

Level 1 Expert

21 Answers

Bill Jordan

Level 2 Expert

372 Answers

Are you a Jandy Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...