Question about Kenmore 16602 / 16604 / 16609 Built-in Dishwasher

1 Answer

Dishwasher kenmore elite model 8530899

My dishwasher runs for over 90 minutes from start to finish. Is there a timeer to reset for a shorter cycle

Posted by on

  • dsconner Jul 05, 2008

    My Kenmore dishwasher 16602 runs for 4 and 1/2 hours on every cycle and has done so since it was new. How can I fix this?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Yes
u go by quick wash its take 28 minutes

Posted on Apr 18, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset Kenmore Elite 665-16572202 Dishwasher...clean light blinks 7 times pauses then repeats. My model does not have a Heated Dry button it has an Air Dry button.


Here's the key sequence(s) to use, depending on how your keys are labeled:
Heated Dry - Normal - Heated Dry - Normal; or
High Temp - Air Dry - High Temp - Air Dry; or
Hi Temp Scrub, Energy Saver Dry, Hi Temp Scrub, Energy Saver Dry; or
High Temp Wash, Heated Dry, High Temp Wash, Heated Dry.

This will start the diagnostic cycle. Let the dishwasher run for a few minutes, and then press Cancel to stop the dioagnostic cycle and clear the error. Please note, that this clears the error, but if you haven't found the cause (water-not-heating error), the condition will come right back the next time you run the dishwasher.

Jan 19, 2015 | Kenmore Dishwashers

1 Answer

Kenmore elite dishwasher manual


The cancel light is on because the cycle maybe paused or canceled. The lit red button should say Cancel/Drain. If you already tried to press start and if it won't finish the cycle then try pressing the Cancel/Drain to drain and start over.

Aug 15, 2014 | Kenmore Elite Stainless Steel 24" BuiltIn...

1 Answer

Dishwasher wont finish any cycles


That blinking light is trying to tell you that there is something wrong with the dishwasher. You need to fix the problem or else that blinking light will come back. And the number of times it blinks (before it pauses and repeats) will tell you (or a technician) what is wrong. How many times does it blink?

Jul 04, 2014 | Kenmore Dishwashers

1 Answer

Kenmore elite dishwasher model 630 Smart Wash light is flashing


You may want to try:
Press a series of four buttons in quick succession. Press "Heated Dry," "Normal Wash," "Heated Dry" and "Normal Wash" to instruct your Kenmore dishwasher to run a short diagnostic test.
Wait for two minutes while your Kenmore dishwasher runs its diagnostic test.
Press the "Cancel/Drain" button once your dishwasher has completed its diagnostic test. This should reset your dishwasher control panel.
Check to make sure that there's no standing water in the bottom of your dishwasher. Standing water in your dishwasher may indicate that your dishwasher has stopped mid-cycle. You will need to press the "Cancel/Drain" button before you can reset your dishwasher control panel.

Dec 18, 2013 | Dishwashers

1 Answer

Dishwasher won't start until running until at


The 2 minutes is most likely the "Fill" time in the cycle therefore since the water supply is active the fill solenoid is spent or not getting a signal.

Dec 12, 2009 | Kenmore Dishwashers

2 Answers

Kenmore Elite Dishwasher clean light ind flashing and won't start


You will have to reset the console. To do this, close the door and press these buttons in sequence...

-high temp wash
-heated dry
-high temp wash
-heated dry

...all the lights will turn on briefly and the machine will start a diagnostic cycle. You can press cancel or let the diagnostic cyle finish (1-2 minutes).
You should now be able to run the dishwasher as normal.

Feb 17, 2009 | Kenmore 24 in. 15142 Built-in Dishwasher

1 Answer

Dishwasher keeps running and countdown stalls randomly.


Sounds like The settings have messed up it happened to mine a while back you need to do a hard reset of the dish washer mine was unplugging the thing then plugging back in 30 seconds later then holding the cycle button a few seconds and then power on again. Find your hard reset combination of what your make and model of the dishwasher is I hope this helps.

Jul 16, 2017 | Kenmore 15952 Dishwasher

Not finding what you are looking for?
Kenmore 16602 / 16604 / 16609 Built-in Dishwasher Logo

Related Topics:

628 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Dishwashers Experts

Ken Johnston
Ken Johnston

Level 1 Expert

56 Answers

Fred Sops

Level 2 Expert

272 Answers

vince

Level 3 Expert

946 Answers

Are you a Kenmore Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...