Question about Kenmore Washing Machines

1 Answer

I have a kenmore 800 series it is full of water but will not wash can i reset it

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 33 Answers

Yes you should be able old is the washer?

Posted on Apr 25, 2010


4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 4088 Answers

SOURCE: I have a kenmore 800 series top load washer. I

Turn off the water at each faucet and remove the hose ends from the washer--place the loose ends in a bucket or sink and turn one faucet on at a time. You should get a fairly large flow of water from each. If near zero, check the faucet end of each hose to look for plugged screens and for any kinks in the hose length. If water flows freely from each hose, then the water inlet solenoid valves in the machine may be inoperative. Open the top to get to the solenoids. Hope this helps!

Posted on Mar 02, 2010

  • 714 Answers

SOURCE: I have a kenmore 800 series top load washer. I

sounds like your water inlet valve

Posted on Mar 02, 2010

  • 15935 Answers

SOURCE: Kenmore Washer series 800 turns off the breaker

For replacement parts - head on over to or and enter in your full model number for a full parts listing.
I recommend both sites because ...

FixYa has no affiliation with either site - I have been using and recommending them for years - trouble free.

PartSelect has a great schematic database for locating the part on your unit and great "testimonials" for each part that often times includes HOW-TO information.
RepairClinic has pictures of each part they sell and also a great how-to and troubleshooting for basic repairs.

If your unit has never been serviced - there should still be an original service manual enclosed in plastic taped to the inside of the shell.
In the service manual are Error codes, maintenance procedures, and troubleshooting steps you can follow.

Anything too complicated or beyond your scope should be handled by a professional.

If you think you want to tackle the repair - and have gotten stuck on a step - reply to your question and I will be glad to help you out.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question)()(*&%$

Posted on Oct 01, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My Kenmore 800 series fills with water then stops completely. Can I reset it or is it more serious?

Hello Suzanne,
It might be more serious than that.
Reply in the comment box with the model number. I should be able to further assist you.
In the mean time here is a link for Sears.
Good Luck!
Water Filters Lawn Garden Appliance Parts

Oct 25, 2015 | Kenmore Washing Machines

1 Answer

I have a Kenmore 800 series washer that won't fill with water, but will go thru the spin cycles if you set it manually, was working fine before except I thought it was using too much water on the auto...

this could be a pressure sw . too ck remove the air tube and blow on the sw it should click . or use a ohm meter to ck it it has 3 wires going to is power in ond power out to valve when it gets full of water it shuts of water and turns on motor .. . the spin does not have anything to with fill & wash . but it does help for the diag of mach ( thanks ) hope this has helped mm feed back pls ..

Nov 08, 2010 | Kenmore 24032\24036 Top Load Washer

1 Answer

Describe your Kenmore 24032 \ 24036 Top Load

Water pump is my first guess. Did you check the hoses that hook to it? The pump is in the front of unit. Give full model number to further assist you.

Jun 15, 2009 | Kenmore 24032\24036 Top Load Washer

2 Answers

Kenmore Series 90 Washer

Aside from complete disassembly & cleaning it, try a hot wash on full with nothing in it except a bunch of bleach. 

Jan 09, 2008 | Kenmore 15864/15862 Top Load Washer

1 Answer

Kenmore "80 Series," model #110.28812790

Sounds like it may be in you pressure switch sounds like it is stuck on full... like you have a full tub or water..

the white part with the hose is the pressure switch

f33c358.jpgck on full... like a full load of water is in the tub

Oct 19, 2007 | Kenmore 24032\24036 Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

339 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Sal De

Level 3 Expert

2699 Answers


Level 3 Expert

5687 Answers


Level 2 Expert

408 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides