Question about Maytag Neptune MAH6500A Front Load Washer

1 Answer

Dryer will not start start/pause button is flashing green; all cycle lights are green

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Maytag Master
  • 43,501 Answers

Hi,

A dryerdryer will not start - 2_bing.gif may not start for many reasons...
This tip that I wrote will help you to figure out what is happening...

http://www.fixya.com/support/r4422207-dryer_repair_dryer_not_turning

http://www.fixya.com/support/r4460438-dryer_repair_dryer_will_not_start

heatman101

Posted on Apr 25, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHY DOES MY DRYER KEEP SHUTTING OFF WITH BLINKING LIGHTS


sure is heres how to get the fault codes

READING ERROR CODES

1. Rotate cycle selector knob to the 3 O'clock position.

2. Press and hold the Select and Pause Cancel buttons simultaneously for six seconds.

3. Immediately after, press and hold the START and Pause Cancel buttons simultaneously for 4 seconds.

4. Rotate the cycle selector knob to the 2 O'clock position. The four indicator lights of Drying, Cool Down, Wrinkle Rid

(Press Saver), and Clean Lint Filter will flash the number of times for the first digit of the code and the START indicator

light will flash the number of times for the second digit. Take separate counts of each indicator light, then repeat to

confirm in order to be accurate in identifying the proper error code. The code is obtained by counting the number of times

the lights flash. Example E24: The four indicator lights would flash twice indicating the 2 and the START indicator light

will flash four times indicating the 4. The four indicator lights and the START indicator light start flashing at the same

time. The control will pause for 2 seconds, then repeat the code.

NOTE: A letter appearing in the code stands for a number higher than nine. A = 10 B = 11 C = 12 D = 13 E = 14 F = 15

Example Code E4A: the first digit would be 4 and the second digit would be 10. The four indicator lights would blink four

times and the START indicator light would blink ten times. Troubleshoot the problem by using the chart below.

To move on to the next code, press the OPTIONS button.

To clear code, press the Select button. Code will be cleared when mode is exited.

To exit this mode, simultaneously press and hold the Select and Pause Cancel buttons for six seconds.

Error Code Label Description Solution

E10 General EEPROM

Fault

Problem with communication

between EEPROM and the

microprocessor.

Clear code, exit mode and start dryer. If problem persists, replace electronic

control.

E11 Checksum Error Problem with communications or

memory did not check, one has

become corrupted.

Clear code, exit mode and start dryer. If problem persists, replace electronic

control.

E12 Non fatal R/W

error

Problem reading or writing to the

memory or input/output.

Clear code, exit mode and start dryer. If problem persists, replace electronic

control.

E24 Control NTC Short

Circuit

Control thermistor or its wiring is

shorted.

Remove wires from control thermistor. Measure resistance of thermistor. If

reading is not 50 K (± 10%), replace thermistor. If reading is within 50 K (±

10%), check wiring between thermistor and electronic control. If good,

replace electronic control.

E25 Control NTC Open

Circuit

Control thermistor or its wiring is

open.

Remove wires from control thermistor. Measure resistance of thermistor. If

reading is not 50 K (± 10%), replace thermistor. If reading is within 50 K (±

10%), check wiring between thermistor and electronic control. If good,

replace electronic control.

E4A Program Timeout

Fault

The drying time has exceeded

program time for that cycle.

Press Pause Cancel and SELECT buttons for 6 seconds to exit test modes.

Position cycle selector to NORMAL, temperature selector to HIGH HEAT

and touch START. Check for anything that would extend dry times such as:

no heat, restricted vent, blower fan blade broken or loose, dryer installed in

closet with solid door, or bad connection in moisture sensor bar circuit or

dirty bars. If dryer operates normally but code returns, replace electronic

control.

E5B Heater Fault (no

heating)

Temperature reading of control

thermistor has not changed in a

certain amount of time.

Position cycle selector to NORMAL, temperature selector to HIGH HEAT

and touch START. Measure voltage across terminals on relay RL2 (heater

relay) on electronic control. If meter reads 240V on electric models and

120V on gas models, replace electronic control. If meter reads zero, remove

power from dryer. Disconnect wire going to NO terminal on the relay RL2.

Reconnect power and measure voltage drop between terminal COM on

relay RL2 and neutral. If meter reads zero, wire between incoming line and

relay RL2 is open. If meter reads 120V, check the rest of the heater circuit.

E68 Key (button) Struck

Fault

One of the keys (buttons) is stuck

closed (active).

Enter function test mode and perform key (button) test to determine which

button is at fault. Carefully free the and perform the test again. If button is

free but the key struck code still exists, replace electronic control.

E8C Too many trips in a

period of time.

The safety (high limit) thermostat

has tripped too many times within

a certain period of program time.

Check for blocked lint filter, blocked exhaust, air leaks around air duct,

broken blower fan blades, worn or loose drum seals, dryer installed in closet

with solid doors or door seal not correctly seated.

EAF Watch Dog Reset Microcontroller has been reset by

internal Watchdog timer.
Clear code, exit mode and start dryer. If problem persists, replace electronic

May 09, 2014 | Frigidaire Dryers

1 Answer

Frigidaire affinity dryer yes code


heres how to get them :


READING ERROR CODES

1. Rotate cycle selector knob to the 3 O'clock position.

2. Press and hold the Select and Pause Cancel buttons simultaneously for six seconds.

3. Immediately after, press and hold the START and Pause Cancel buttons simultaneously for 4 seconds.

4. Rotate the cycle selector knob to the 2 O'clock position. The four indicator lights of Drying, Cool Down, Wrinkle Rid

(Press Saver), and Clean Lint Filter will flash the number of times for the first digit of the code and the START indicator

light will flash the number of times for the second digit. Take separate counts of each indicator light, then repeat to

confirm in order to be accurate in identifying the proper error code. The code is obtained by counting the number of times

the lights flash. Example E24: The four indicator lights would flash twice indicating the 2 and the START indicator light

will flash four times indicating the 4. The four indicator lights and the START indicator light start flashing at the same

time. The control will pause for 2 seconds, then repeat the code.

NOTE: A letter appearing in the code stands for a number higher than nine. A = 10 B = 11 C = 12 D = 13 E = 14 F = 15

Example Code E4A: the first digit would be 4 and the second digit would be 10. The four indicator lights would blink four

times and the START indicator light would blink ten times. Troubleshoot the problem by using the chart below.

To move on to the next code, press the OPTIONS button.

To clear code, press the Select button. Code will be cleared when mode is exited.

To exit this mode, simultaneously press and hold the Select and Pause Cancel buttons for six seconds.

Error Code Label Description Solution

E10 General EEPROM

Fault

Problem with communication

between EEPROM and the

microprocessor.

Clear code, exit mode and start dryer. If problem persists, replace electronic

control.

E11 Checksum Error Problem with communications or

memory did not check, one has

become corrupted.

Clear code, exit mode and start dryer. If problem persists, replace electronic

control.

E12 Non fatal R/W

error

Problem reading or writing to the

memory or input/output.

Clear code, exit mode and start dryer. If problem persists, replace electronic

control.

E24 Control NTC Short

Circuit

Control thermistor or its wiring is

shorted.

Remove wires from control thermistor. Measure resistance of thermistor. If

reading is not 50 K (± 10%), replace thermistor. If reading is within 50 K (±

10%), check wiring between thermistor and electronic control. If good,

replace electronic control.

E25 Control NTC Open

Circuit

Control thermistor or its wiring is

open.

Remove wires from control thermistor. Measure resistance of thermistor. If

reading is not 50 K (± 10%), replace thermistor. If reading is within 50 K (±

10%), check wiring between thermistor and electronic control. If good,

replace electronic control.

E4A Program Timeout

Fault

The drying time has exceeded

program time for that cycle.

Press Pause Cancel and SELECT buttons for 6 seconds to exit test modes.

Position cycle selector to NORMAL, temperature selector to HIGH HEAT

and touch START. Check for anything that would extend dry times such as:

no heat, restricted vent, blower fan blade broken or loose, dryer installed in

closet with solid door, or bad connection in moisture sensor bar circuit or

dirty bars. If dryer operates normally but code returns, replace electronic

control.

E5B Heater Fault (no

heating)

Temperature reading of control

thermistor has not changed in a

certain amount of time.

Position cycle selector to NORMAL, temperature selector to HIGH HEAT

and touch START. Measure voltage across terminals on relay RL2 (heater

relay) on electronic control. If meter reads 240V on electric models and

120V on gas models, replace electronic control. If meter reads zero, remove

power from dryer. Disconnect wire going to NO terminal on the relay RL2.

Reconnect power and measure voltage drop between terminal COM on

relay RL2 and neutral. If meter reads zero, wire between incoming line and

relay RL2 is open. If meter reads 120V, check the rest of the heater circuit.

E68 Key (button) Struck

Fault

One of the keys (buttons) is stuck

closed (active).

Enter function test mode and perform key (button) test to determine which

button is at fault. Carefully free the and perform the test again. If button is

free but the key struck code still exists, replace electronic control.

E8C Too many trips in a

period of time.

The safety (high limit) thermostat

has tripped too many times within

a certain period of program time.

Check for blocked lint filter, blocked exhaust, air leaks around air duct,

broken blower fan blades, worn or loose drum seals, dryer installed in closet

with solid doors or door seal not correctly seated.

EAF Watch Dog Reset Microcontroller has been reset by

internal Watchdog timer.
Clear code, exit mode and start dryer. If problem persists, replace electronic

May 06, 2014 | Frigidaire Affinity 5.8 Cu. Ft. Gas Dryer

1 Answer

Unlocking your washer so it actually works.


If the green cycle light is flashing on then off, this usually means the cycle is paused. The lid lock should unlock when in pause mode, if not you will need to press and hold the "Pause/Play" button to clear the cycle completely, if there is water in the unit, it will drain first, then unlock the lid and be on standby to start a new cycle. Pleazer Appliance...

Apr 13, 2014 | Amana NTW4700YQ Top Load Washer NTW4700YQ

1 Answer

I have a whirlpool adp6600 dishwasher. the green light just keeps flashing (i think it's 7 times in a row each sequence) and the cycle won't start. have tried turning it off at the wall, clean


Dishwasher is in fault mode hold start/pause button for a few seconds this will reset the unit run your cycle again if dishwasher faults again call you local service man.good luck

Aug 02, 2012 | Whirlpool Dishwashers

1 Answer

I have an Electrolux EWD1477. I have been away for four months and I'm having problems with it. I set to do the quickwash30 program and press start, you hear the clicks, it might put some water in then...


My EWD1477 was doing this a year ago and I fixed it. Then it started doing it again a month ago and I seem to have cleared it again.

Firstly, remove the drain hose from where it is inserted into a laundry sink hole to make sure it is not blocked or sealed in with sludge.

Secondly, make sure the machine is empty of water and clothes and then turn the machine to off with the Program Selector Dial. Then turn off the power at the socket and remove the power plug and leave for five minutes.

Step 1: put the plug back in and turn the power back on.

Step 2: turn the selector switch to the right (Whites/Intensive). The green light of the Start/Pause button should be flashing and the green lights on for Prewash/wash, Rinses and Spinning. Don't press any other buttons or change any other settings.

Step 3: press the Start/Pause button and wait for the machine to empty any excess water. Press it again immediately after you hear water flowing into the machine OR two audible clicks. The machine is now in pause mode with the green light of the Start/Pause button flashing. Only the green light on the Prewash/Wash button should be on. Leave it in pause mode for 30 minutes and then press the Start/Pause button to recommence the cycle.

Step 4: If the Start/Pause button begins flashing, water stops flowing into the machine and the three green lights mentioned above are back on, turn the Program Selector Dial back to off, wait 10 seconds, and repeat the process above.

Step 5: If when you then turn the Program Selector Dial to Whites/Intensive and hear the two audible clicks, immediately press the Start/Pause button to set the machine in pause mode. Wait 30 minutes. Then press the Start/Pause button to recommence the cycle.


Hopefully the cycle will run without a problem.

Mar 26, 2011 | Electrolux Washing Machines

1 Answer

Start button will not initiate on cycle. Get 3 beeps.


Hi,
There can be many reasons why your dryer2_bing.gif will not turn...

This tip that I wrote will help you to figure out what is happening...

Dryer2_bing.gif Repair - The Dryer2_bing.gif is not Turning
http://www.fixya.com/support/r4422207-dryer_repair_dryer_not_turning

Dryer2_bing.gif Repair ? The dryer2_bing.gif will not start
http://www.fixya.com/support/r4460438-dryer_repair_dryer_will_not_start


heatman101

Jun 20, 2010 | Whirlpool GEW9250 Electric Dryer

1 Answer

40C cycle stopped with 12 mins on display - now nothing works


Press "end of cycle" & wait for 2 minutes then try the door, do not force the door........................ If problem persists go to your model above & click on your model number & look for solutions....should find something.

Jan 12, 2008 | AEG Lavamat 16810 Front Load Washer/Dryer

1 Answer

Error code DR


Pull the tech sheet out of the dryer ( behind the lower front access panal ). The lights flashing are trying to tell you a fault code.

A copy:

MODEL DIFFERENCES: • Better models have a digital readout display
• Good models do not have a digital readout display
READING ERROR CODES 1. Position cycle selector knob to the 3 O’clock position.
2. Press and hold the Select and Pause Cancel buttons simultaneously for six seconds.
3. Immediately after, press and hold the START and Pause Cancel buttons simultaneously for 4 seconds.
4. Rotate the cycle selector knob to the 2 O’clock position.
On better model dryers, the error code will appear in the digital display. On good models, the five indicator lights of
Drying, Cool Down, Wrinkle Rid, and Clean Lint Filter Spin will flash the number of times for the first digit of the code
and the START indicator light will flash the number of times for the second digit. Take separate counts of each indicator
light, then repeat to confirm in order to be accurate in identifying the proper error code. The code is obtained by counting
the number of times the lights flash. Example E24: The five indicator lights would flash twice indicating the 2 and the
START indicator light will flash four times indicating the 4. The five indicator lights and the START indicator light start
flashing at the same time. The control will pause for 2 seconds, then repeat the code.
Note: A letter appearing in the code stands for a number higher than nine.
A = 10 B = 11 C = 12 D = 13 E = 14 F = 15
Example Code E4A: the first digit would be 4 and the second digit would be 10. If this code would appear on a dryer in
the Good model line, the five indicator lights would blink four times and the START indicator light would blink ten times.
Troubleshoot problem by using chart below.
To move on to the next code, press the OPTIONS button. To clear code, press the Select button.
To exit this mode, simultaneously press and hold the Select and Pause Cancel buttons for six seconds.

jeff.
__________________
http://www.applianceaid.com/
Appliance Repair Aid
http://www.jrappliance.ca
JRAppliance

Jan 10, 2008 | Frigidaire AEQ7000ES Dryer

2 Answers

3 beeps mean what


If the only thing that happens is three rapid beeps when you select a feature from the console this is usually a symptom of a defective door switch.  The door switch must be closed to complete the circuit from the timer to the heating circuit and drive motor.  If the switch is bad, or the wiring is broken, the dryer will not run.

Oct 17, 2007 | Kenmore 62062 Electric Dryer

Not finding what you are looking for?
Maytag Neptune MAH6500A Front Load Washer Logo

197 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

587 Answers

John Tripp
John Tripp

Level 3 Expert

4654 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...