Question about Rockford Fosgate Punch 201S Car Audio Amplifier

1 Answer

Need a diagram

I need a diagram to wire my amp to my car stereo the amp is a rockfosgate 201s 600 watts & im hookimg it up to a jvc stereo thank u for your time

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

You have to take a positive cable with fuse placed near to the battery to your amplifier B+ and a thin wire from the jvc sterei to the amp for the remote REM and an RCA cable for the sound system the negartive wire keep it short as you can and connect it to the chassis

Posted on Apr 26, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I bought a mtx terminator amp model no TNA251 600 watt and two subs installed. It works good for few days but now its not cranking up proper bass and sound. It always has three solid red lights everytime....


does it do this all the time when you turn it on? any sound at all?
provide more information, but my guess its that the amp is blown. replace it or sell it for parts.

Nov 11, 2013 | Car Audio & Video

1 Answer

Rockford 201s 600 watt amp turns on but no sound going to the subs and where is the fuse on these?


there is no fuse you need a cable that goes to the battery that has a fuse check you're ground

Nov 02, 2010 | Rockford Fosgate Punch 201S Car Audio...

1 Answer

Car audio amplifer blowing fuses


why are you in stereo for subs? mono all the way.

Feb 21, 2010 | Kenwood KAC-7252 Car Audio Amplifier

1 Answer

Amp keeps blowing the fuses


Serious short circuit on your output transistors, need replacing.

Sep 28, 2009 | JVC KSAX4504 MOSFET 600-Watt Amplifiers...

1 Answer

JVC 600 watt amp overheated


Yes it has a protection mode, let it cool for while then try it again, if it over heats quick make sure you're not running the amp below its stable impedance.

Aug 30, 2009 | JVC KSAX4504 MOSFET 600-Watt Amplifiers...

1 Answer

What is the very best way to wire 3 sets of speaks and 2 subs through a 4 ch. amp and a 2 Ch. amp.?Thank you, Paul


Ummmm Im gonna give this a try-If it were me i would run the 4 channel ground pounder on the doors and rear panels -the front 2 channels run the component set exclusively at 2 ohms per channell and run the 8 inch 3 ways in parallel with the rear deck speakers for a combined load of 2 ohms per channel on the rear channells-naturally the 8 inchers and the 6.5's are going to be able to handle a little bit more bottom end than the component set so you can feed a little more midbass to those rear channels- I dont know the resistance of the coils on your subs or the model of the MA amp you are using but if you can throw 600 or 700 on your subs that should be sweet enough- hope its not a waste of your time or maybe you already tried it set up that way-good luck though

May 27, 2009 | Alphasonik (PMA640A) Car Audio Amplifier

1 Answer

Can a rf 201s amp push 4-6x9s and 4-104s door speakers


Hello jon_jonmay,

Wiring 4 speakers to each of 2 channels, you will need to wire them series-parallel and run them at 4 ohms. If you wire all 4 parallel, the load will be 1 ohm and the amp is only stable down to 2 ohms.

According to your manual, the 201s will deliver 50 watts into each channel at 4 ohms . So it will be supplying about 12.5 watts per speaker which is about what you get with the average factory radio. They will work OK, but they're not going to be very loud.

Hope this helps.

Apr 21, 2009 | Rockford Fosgate Punch 201S Car Audio...

2 Answers

Need a wiring diagram for car stereo f65f-19b165-bd A speaker wire diagram is needed for a 1997 Ford Expedition with stereo part number F65F-19B165-BD.  I have purchased a JVC HD Radio and will be...


why not put a belson car radio that uses a sd chip card and a usb connection ,a 1gb sd card is about 30 cds so why mess about with the cd changer ,old technology ,would you put an 8track in it ?? or a mobile vinyl 45 record player

Jan 14, 2009 | 1997 Ford Expedition

Not finding what you are looking for?
Rockford Fosgate Punch 201S Car Audio Amplifier Logo

388 people viewed this question

Ask a Question

Usually answered in minutes!

Top Rockford Fosgate Car Audio & Video Experts

seankane89

Level 1 Expert

27 Answers

Tygh Duval
Tygh Duval

Level 2 Expert

300 Answers

Professor_V
Professor_V

Level 2 Expert

92 Answers

Are you a Rockford Fosgate Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...