Question about Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher

1 Answer

The top drawer of my fisher paykel dishwasher stops during the cycle and shows an icon of a tap with a line threw it (assume that means no or low water pressure). the bottom works fine so I assume water pressure is not the issue; is there a sensor that could be bad? Also, I did switch the controllers between drawers (good instructions on the fisherpaykelparts.net website) but the problem stayed with the drawer, ruling out the controller.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Fisher and P... Master
  • 713 Answers

Did it fill with water? could be 1 of your water valves is faulty, or the little filter for the inlet water is blocked. please reply 4 more help. i"m sure i can fix this problem for you. good luck.

Posted on May 05, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

F2 code on Fisher Paykel dishwasher


The problem is linked to rotor operation during discharge cycle. By replacing the rotor with bottom will only address part of the problem. There is very likely some obstruction in the pump cavity. This is the small channel connecting the drain sump and the pump cavity. Grab a thin but rigid wire and clear this channel. Usually a bone chip or some seed.
Also confirm if the top rotor worked ok when you moved it to the bottom drawer.

Mar 09, 2013 | Fisher and Paykel 23 in. DD-603SS Built-in...

1 Answer

Fisher and paykel DD605 stops at 25 mins


Most likely a fault with the heater element. Check if the water is warm when it stops during a heavy wash cycle.

Mar 01, 2013 | Fisher and Paykel Dishwashers

1 Answer

Bottom dishwasher of fisher and paykel wont drain


Check the filter sump is clear and there are no blockages in the rotor cavity. If you hear the rotor noise when it is in drain cycle then blockage is inside the rotor or filter sump cavity. Assuming the top drawer is working ok, the drain hose at kitchen end might be ok. The drain hose within the drawer could also be an issue. Try to run the dishwasher with a Finish dishwasher cleaning kit (from super market) after following the instructions on the kit. First empty dishwasher with a small cup.
If the rotor is silent during drain cycle then you have a bigger problem - faulty rotor circuit.

Jan 17, 2013 | Fisher and Paykel 23 in. DD-603SS Built-in...

1 Answer

Machine Running noisy during cycle


lift off spray arm and remove motor rotor and remove any debri this can cause a noisey motor.

Sep 04, 2012 | Fisher and Paykel 24 in. DD603H W Built-in...

1 Answer

Fisher Paykel double drawer built in top drawer stops mid cycle.


It would help to know which LEDS are on when it stops. Are you able to open the lid etc. Does this happen with the short rinse cycle as well?

Oct 17, 2010 | Fisher and Paykel 23 in. DD-603 Built-in...

1 Answer

I have a Fisher and Paykel 2-drawer dishwasher. The top drawer is stuck in the rinse cycle and I cannot change it to another cycle. Please advise.


Assuming the controller of the top drawer is still ok, take a clean damp cloth and wipe the top panel where the program keys are located.

If nothing happens, you will have to check if the controller connector is not loose. Take the front cover off and check the controller connectors.

Please rate this solution to help fixya serve you better in future.

Sep 16, 2010 | Fisher and Paykel 23 in. DD603H SS...

1 Answer

Fill Fault appears during wash cycle.


Is the filter in the hose where it screws onto the tap clean?, if this is okay then most likely the valve.

Apr 19, 2010 | Fisher and Paykel 23 in. DD-603SS Built-in...

1 Answer

Fisher paykel DD603 top drawer starts cycle then stops and beeps and doesn't go thru cycle


When it stops and beeps can you tell me all lights that are on when you open the drawer cheers. also check to see if the water in the tub is hot if not you have a heating issue. either a faulty element or Mtr Controller module. try swapping the Mtr Controller module (computer board) from the top drawer to the bottom drawer and see if that moves the fault. cheers

Mar 07, 2009 | Fisher and Paykel 23 in. DD-603SS Built-in...

Not finding what you are looking for?
Fisher and Paykel 23 in. DD-603SS Built-in Dishwasher Logo

304 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Dishwashers Experts

Brian Coughlan

Level 2 Expert

275 Answers

marley mcelhinney

Level 3 Expert

490 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18389 Answers

Are you a Fisher and Paykel Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...