Question about Ryobi Cultivator

2 Answers

Gas lines on ryobi cultivator 410aa fell off. replaced lines, tank, and the bulb. will not crank. need info on where line go

Posted by on

  • laryms Apr 23, 2010

    I have this drawing does not show where each gas lines connect on both ends I think I have them on wrong.

  • laryms Apr 23, 2010

    i have drawings does not show where both ends of lines connect have done screws and gasket

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 344 Answers

Exploded view:-
http://www.outdoordistributors.com/pdf/Ryobi/RYOBI-410.pdf

Did you replace the gasket (item 15 on the linked document) when replacing tank and lines, if you didn't and the old one has been torn it could be sucking in air, also the 4 carb mount screws need to be of equal tightness

Posted on Apr 23, 2010

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 666 Answers

I am guessing that you took the top cover plate loose to replace the fuel tank, you may have an air leak between this plate and the crankcase. This could cause a problem like the one you describe, although it could also be the carburetor causing this problem.

Assuming that is was running ok prior to replacing the fuel tank, I would have to think there is a good possiblilty of an air leak.

im going to also link a schematic for it so you can see exactly what you need to

http://www.outdoordistributors.com/pdf/Ryobi/RYOBI-410.pdf


hope this helps
please leave feedback thanks
Robb

Posted on Apr 23, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Air in fuel ryobi tiller


you will have 2 lines at the tank. 1 is the supply line with one end having the fuel filter on it and sitting at the bottom of the tank. it generally runs to the inlet side of the carb. the output side of the carb usually goes to the primer bulb inlet, the last hose usually goes from the outlet of the primer bulb back to the fuel tank but only goes in 1/8 to 1/4 of an inch. it should only be in far enough to seal the hole and allow the fuel back in to the tank

Mar 29, 2013 | Ryobi Cultivator

1 Answer

Fuel line diagram for sears mini cultivator


hello sir,routing fuel line for craftsman,homelite,ryobi,hedge and line trimmers,fuel tank under engine, looking at machine from rear, shall fuel line on left with filter attached goes to bottom port of carb, fuel line from right side coming out of tank with inside tip attached goes to bottom port of primmer bulb,top line on primmer bulb goes to top port of carb, fuel tank under engine,fuel line routing,looking at machine from left side, left fuel line coming out of tank(drain back only) goes to right side small port of primmer bulb, left side larger fuel line from primmer bulb to top port of carb, fuel line coming out of tank (larger line) on the right side with filter attached goes to bottom port of carb, when replacing fuel line it is very important to use the same ID and OD line the homelite takes a special line that is black in color and a bigger size,the bigger line is ID .08-OD140 small line ID3/32 X 3/16.when the lines dissolve small pieces will get in the carb clogging small passages and screen,it is advisable that you clean out carb,and use a new filter.hope this helps,any comments welcome,thank you. if the filter has broken off of the line half way that is where you will run out of fuel, ``

Feb 17, 2012 | Ryobi Garden

1 Answer

Hello, my Ryobi 410r tiller/cultivator needed new fuel line so I bought the fuel line, return and a new bulb primer. Unfortunately, I can't remember what hose goes where!!! Specifically, I've...


The primer pulls fuel through the carbruetor
So take your return line from the carb. and hook it to the inlet side of the primer and the other side
of the primer bulb transtions into the fuel tank.
You know when you have hooked it up right when you press the primer it fills with fuel and dumps back into the tank.

Jun 16, 2011 | Ryobi Garden

1 Answer

The gas line for the in-gas filter corroded. Does it go to the pump bulb or carburator and how far down do both lines go?


The longest, and sometimes smaller in diameter of the two fuel lines, goes from the carburetor to the bottom of the tank. Leave enough slack in this line so that the filter that attaches to the end will rest comfortably at the bottom of the tank.

The other fuel line goes from the primer bulb to just inside the tank, (about an inch). make sure that you get the right size fuel lines. The plastic coupling goes on the end of this line, inside the tank. This keeps the line from pulling out of the tank.

(HINT): When feeding the lines through the tank holes, cut the lines at an angle. They will feed much easier into the holes. You can than cut them off square, once you know that you have enough to work with.

If you need further assistance, just let me know.

Jim

Sep 03, 2010 | Ryobi Cultivator

1 Answer

Ryobi cultivator won't start. Just had the gas lines replaced


it could be a pin hole leak in the primer bulb.

Jun 21, 2010 | Ryobi Cultivator

1 Answer

Replaced gas lines on ryobi 31ccweedeater. my have lines crossed. will not crank.


One fuel line (the one with the fuel filter in the end of it), comes out of the tank and goes to the bottom fitting on the carburator. The second line comes out of the tank and goes to the bottom fitting on the primer bulb. The third section of fuel line goes from the top fitting on primer bulb to the top fitting on carburator. That should be the correct fuel line routing. Hope this helped and best wishes.

Aug 28, 2009 | Ryobi 30 Cubic Centimeter Curved Shaft Gas...

1 Answer

Fuel line routing. Never clear enough Explaination.


need brand name of your unit, but reading what you have I will say that the thick one from tank goes to carb and the thin one goes from primer bulb to tank as a return, for fuel. need more info!!

Jul 14, 2009 | Ryobi Cultivator

1 Answer

There are two hose/line openings in the gas tank of my Ryobi 410r cultivator. Where and which do these two lines go to? Which of them goes to the primer bulb? Also, there are two lines to/from the primer...


IT SOUNDS LIKE A TWO CYCLE ENGINE TO ME. THE HOSE GOING TO THE PRIMER BULB GOES TO THE HOSE THAT SITS ON THE TOP OF THE TANK AND DOEST GO IN FAR AT ALL AND IS USUALLY THE BACK. THE OTHER HOSE GOES IN THE NID PART OF THE TANK OR THE PART THAT THE GAS IS AT ITS HIGHEST POINT IN THE TANK WHEN THE UNIT IS IN THE POSITION MOST LIKE IT IS WHEN IN USE USUALLY THIS HOSE HAS A SMALL FILTER IN THE TANK. THIS SYSTEM OPERATES ON PRESSURE. WHEN YOU PUMP THAT BULB, IT PRESURIZES THE TANK FORCING GAS UP THROUGH THE OTHER LINE TO THE CARB. IF YOU ARE SYING THERE IS A 3RD HOSE HMMM, THAT PROBABLY GOES TO THE MIDDLE PART OF THE CARB
REGARDS

Jun 30, 2009 | Ryobi Cultivator

2 Answers

Gas lines broken


does it have a pump bulb on the side of the carb? if so,it could have a pin hole in it a be sucking air.

Apr 26, 2009 | Ryobi Cultivator

2 Answers

Ryobi Cultivator 410r


The linefrom the tank with the filter goes to the mixture inlet on carb. The fuel return goes to the suction side of bulb. The bulb outlet line goes to the tank. Hopes this helps

Mar 19, 2009 | Ryobi Factory Reconditioned 18" 40cc...

Not finding what you are looking for?
Ryobi Cultivator Logo

1,317 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ryobi Garden Experts

Nick Olsen

Level 2 Expert

183 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Are you a Ryobi Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...