How to configure router d-link - D-Link DI 514 Wireless Router (DI-514)

Basic steps to configure your router:

1. Set Up IP Address and Sub-net Mask for their router.
2. Now open the router Web Page by 192.168.0.1 in the browser URL.
3. Login with your User Name and Password.
4. For Manuall Configuration and Set-up router according to your ISP.

Router have different configuration according to Model. for more router support http://support.dlink.com/ and any router related technical support D-Link Router Support .

YES THATS TRUE. TO CONFIGURE THE ROUTER. NEED THE PPPOE USERNAME AND PASSWORD FROM THE INTERNET SERVICE PROVIDER. VPI AND VCI SETTINGS.
..THEN ACCESS THE ROUTER PAGE
..GO TO ADVANCE SETUP PAGE.
..THEN LAYER2 INTERFACE
..CLICK ADD
..CONFIGURE THE SETTINGS.
..POWER CYCLE THE NETWORK.

Try resetting the D-Link back to the defaults and then configure the router again.
To reset the D-Link back to the default settings -
Press and hold the RESET button at the back of the router with the power ON untilthe LEDs flash at the time the release the RESET button.
Connect a LAN cable from the D-Link to your laptop/computer's LAN port, openthe browser on your laptop/computer and enter the D-Link's configuration URL..
http://192.168.0.1
The default login = admin
The default PW = blank (just press Enter) You can now change the default password.
You can now configure the wireless settings. Now configure the wireless card in your computer/laptop withthe router's wireless settings.
To secure your wireless network from unauthorized access,please click on this link and follow my instructions :- http://www.fixya.com/support/r3559128-wireless_router_security

If you're connected to the router, navigate to http://192.168.0.1/ . If you're trying to configure the router remotely, that's a lot more difficult. You'll have to check your manual for more information on that. (Or I can scour through the manual for you.)

D links are normally pretty user friendly. Try resetting the router itself. grab a paperclip or something small, and hold down the reset button in the back of the router for 10 sec. or until it resets by itself. once this is done your router should be restored back to default settings, aka. like when you first took it out of the box.

Connect a LAN cable from the D-Link to your computer's LANport, open a browser and enter the D-Link's configuration URL. OR open thebrowser on your laptop and enter the D-Link's configuration URL..
http://192.168.0.1
The default login = admin
The default PW = blank (just press Enter)
You can now go to the wireless settings eg. SSID, WPA or WPA2 encryption key.
Now you need to configure the wireless card in the VISTA computer with the router's wireless settings for this computer to communicate with the D-Link router.

You can install the CD on wired or wireless computer.However,if you are using any wireless computer to install the router using CD then,turn-off the third party wireless utility on the computer.

If you are still unable to configure the router then,you can configure the router manually.

If your Internet Service Provider is Cable follow this link to configure the router.

If your Internet Service Provider is DSL follow this link configure the router.

start - run- type in cmd- enter- type in ipconfig /all will show router address should be 168.192.1.1
open internet explorer and type that # in the address bar
should connect with router
leave password blank or type in password for the password
enter the router setup and configure router to your preferance

Hi,

Check DHCP/Manual IP configuration at both ends. I think Router is configured for manual IP configuration and Laptop is configured DHCP.



Regards;
Hassan

Yes, Netscape 6.2 will work properly with the web page-based interface used in D-Link DSL routers, however, due to problems the browser has loading Java applets and working with Java scripts all of the features may not be visible. Netscape 4.7 does work with the interface, but is extremely slow in loading the various configuration pages. For these reasons, it is recommended to use Microsoft Internet Explorer 5.x or 6.0 to configure D-Link DSL routers. Internet Explorer loads the pages faster and Java applets work properly, as shown below. Note the tree in Fig. 1 (using Internet Explorer), representing the router´s various configuration pages and in Fig. 2, the PPP Connection information. Using Netscape 6.2 as shown in Fig. 3, the configuration tree is missing and in Fig. 4 the PPP Connection Information is not displayed.