Question about Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher

Open Question

Whirlpool dishwasher GU980 model

Have Whirlpool dishwasher, Gold series with the touch panel. It stops part way through the wash & rinse cycles with the normal led swithc panel blinking...open ing doors seem to let it continue...but sometime never stop running ......is it the touch panel that is bad normal switch stuck on or electroninc control module

ran the diagnostics cyclce.....but doesn't indicate anything. Model GU980SGC

Posted by on

  • robertwpicke Mar 25, 2009

    the washer will not come off of the delay cycle and turns on and off when ever it pleases

  • Anonymous May 07, 2009

    The cycle starts and stops repeatedly and two of the led lights blink while it's stopped. It eventually finishes the cycle, but takes way too long.

×

5 Suggested Answers

markevans
  • 148 Answers

SOURCE: problems with Whirlpool dishwasher model GU1500XTKB0

will these units (silo and jtrip) start back on their own? if so, it is likely they are heating the water.
otherwise it sounds like a logic board, unless there is a defective door switch or sensor issue.
electronics seem to be a recurring problem with whirlpool.
i would ask whirlpool (electorlux) to either buy it back or fix it.
good luck
mark

Posted on Dec 28, 2007

  • 1073 Answers

SOURCE: problems with Whirlpool dishwasher model GU1500XTKB0

have they checked the thernals on the bottom of the tub

Posted on Apr 12, 2008

  • 4 Answers

SOURCE: Dishwasher lights blinking

QuietGuard3: Clean light flashing 7 times? Press Heated Dry, press Normal Wash, then press Heated Dry again and press Normal Wash again (that's 4 button-presses) and that should fix it.

Posted on Jul 01, 2008

  • 1 Answer

SOURCE: Whirlpool Quiet Partner II not washing or sensing.

I have a whirlpool quiet partner II and for some reason it does not drain the water out any more and I cannot figure out why....people say that it is the filter but that is unbelievably hard to get to and I cannot find any instructions online or paper work that tells how to break it down. If anyone has any insight please let me know

Posted on Nov 23, 2008

  • 3 Answers

SOURCE: We have a Whirlpool Gold

I replaced the heater element on mine and that fixed the problem.

Posted on Mar 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does it beep through the entire. Wash cycle. No code showing.


Whirlpool Duet GHW9150P Front Load Washer Beeping ...

www.fixya.com > ... > Whirlpool Duet GHW9150P Front Load Washer
Question about Whirlpool duet Washing Machines ... my front loader is not workingwhirlpool washer flashes and beeps will not finish a cycle 1 Beep/E10--Error: Water... It beeps through the wash and rinse cycle every couple of minutes. ... Cycle signal which tells you that the cycle is complete beeps through the entire cycle.

[PDF]front-loading automatic washer use and care ... - Whirlpool

www.whirlpool.com/.../U...

Translate this page Whirlpool Home AppliancesWash. This is the main portion of the wash cycle. You will see the washer tumble the load. ... Spin cycle. If the laundry is still wet, take half of the load out of the washer and try again. .... Using recommended AFFRESH® washer cleaner, add.

[PDF]DISHWASHER USER INSTRUCTIONS - Whirlpool

https://www.whirlpool.co...

Translate this page Whirlpool Home AppliancesThe first cycle using the sensor will run longer to calibrate the optical sensor. Rinse Aid. Using rinse aid will optimize your drying and wash performance. This dishwasher is ...... laundry detergent, hand soap, or dish detergent for hand washing .... models) you will experience more starts and stops throughout the entire cycle.

Continuous Beeping - Whirlpool Duet Sport Washer - The ...

appliantology.org > ... > The Laundry Appliance Repair Forum

Jan 25, 2016 | Whirlpool Washing Machines

1 Answer

On rinse cycle...cannot control water temperature...set it for warm but still feels cold to touch. wash cycle is ok. model is whirlpool gold ultimate care II..top loader.


Is the hot water turned on. Remove hose from washer and check screen in water inlet. If it is clear you may need a new water inlet valve.

Apr 01, 2011 | Whirlpool Ultimate Care II LSQ9564J Top...

1 Answer

I have a Whirlpool Gold Dishwasher Quiet Partner IV. GU Series. It has stopped working and there are no lights on the panel. We have checked the power supply and that is fine.


Hello & Welcome to FixYa

Press and hold the AIR DRY/RINSE ONLY button to reset the control, if you have already tried this and it is possible that the door was opened while in cycle then the first thing that should be checked is the door switch/lock assembly. You can take a hair dryer and try to blow air on that, if the problem returns then replacing the door switch/lock assembly is recommended repair. Please get back to me if you have any other questions.

Kevin

Dec 11, 2010 | Whirlpool Gold 24 in. Built-In Dishwasher...

1 Answer

My 6 year old Whirlpool dishwasher is loud


This is a bad wash pump. Looking at about $175 for just the sump assembly. You could do it yourself, but unit would need to be uninstalled.

May 28, 2010 | Whirlpool Gold 24 in. Built-In Dishwasher...

1 Answer

Most Buttons on Front Panel of Whirlpool Gold IV not Working


Did you get an answer? I'm having the same problem

Sep 25, 2009 | Dishwashers

1 Answer

Kenmore dishwasher stops midway through


http://fixitnow.com/wp/2006/03/29/whirlpool-kitchenaid-kenmore-dishwasher-poor-cleaning/
Here is a good page that can help you resolve this issue and buy the parts needed

Feb 14, 2009 | Whirlpool Gold 24 in. Built-In Dishwasher...

1 Answer

Whirlpool gold builtin dishwasher


Do not recommend premeasured tablets, usually too much soap. If pre-rinsing dishes use only 1 or two teaspoons of soap in the main wash cup..do not put soap in the prewash cup. Excess soap can cause oversudsing and make the soil sensor think the dishes are real dirty initiating additional wash cycles. Use rinse-aid for better drying performance

Apr 28, 2008 | Whirlpool Gold 24 in. Built-In Dishwasher...

1 Answer

Have Whirlpool dishwasher Gold Series, Model GU9805CGB1 which stops part way through wash cycle with the led indicator blinks on the normal cycle.....if we ope nthe door and shut ...it continues until part...


sounds like the door is losing contact with the door switch, first thing i would check is the door strike.Metal strike plate located on the tub itself that the door latch catches as it closes. its a spring metal striker, i would try bending it down a little bit to ensure better contact with the switches inside the door itself . next id open the control panel and check to make sure your door switches are secured well, wires are tight.

Mar 22, 2008 | Dishwashers

Not finding what you are looking for?
Whirlpool Gold 24 in. Built-In Dishwasher Dishwasher Logo

Related Topics:

330 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Mike

Level 3 Expert

4334 Answers

Owen Barnes

Level 3 Expert

867 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...