Question about Washing Machines

Simpsom Washing Machine

Hi,
Wash machine not holding water to set level, when washing and trying to soak a load the water leaks out the waste hose even when washer is off.
Machine is 12moths old hope you can help.

1 Answer

prem mathew

Level 3:

An expert who has achieved level 3 by getting 1000 points

All-Star:

An expert that got 10 achievements.

MVP:

An expert that got 5 achievements.

President:

An expert whose answer got voted for 500 times.
Master
1,294 Answers

First see that the exit hose behind the machine is at the correct height, before coming down into the wall standpipe or your sink. Your machine pump pumps water over this height, about 2.75 feet above ground level. Possible there is a water level height marked behind your machine.

If water flows out when machine is off, possible your inlet valve at top of machine is defective...............can be replaced easily.

Posted on Mar 22, 2008

1 Suggested Answer

6ya staff

2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Instant Repair Help over the Phone

6ya.com

Save Time & Money by instantly connecting to...

Posted on Jan 02, 2017

Add Your Answer

Upload

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

Error code 13. Turned water on to machine and it leaked.

Try this link

it says the following:
E13 Condition Water leak in the tub or air leak in pressure-switch air hose Check/Repair The washer fills for too long without the water level pressure switch tripping to indicate that the washer is full. Check for a leak in the wash tub. If the tub is not leaking, check to see if the washer is overfilling. If it is, check the air hose and water-level pressure switch for problems.
Shop Parts Outer wash tub, Air hose, Water-level pressure switch
Frigidaire Front Load Washer Error Codes Sears PartsDirect

Jun 09, 2015 | Frigidaire Washing Machines

1 Answer

I have miele w500 problem is the soak/pre-wash

hi, the problem you are having with the "soak/prewash" light flashing after the wash has started is a common fault on the meile washing machine. Its a water sensor problem. remove all srews and bolts from front of machine and open the front panel. you will see a red in colour pressure switch at one oclock, there will be a black tube attached to it, remove the tube and replace it with a new one, or reverse the tube in reverse and you will find that the water intake level will be less and the fault of the "soak/prewash" light will no longer flash, problem solved. 0868887054 DAVID ASHBOURNE. MEATH.

Nov 14, 2012 | Miele Novotronic Premier 500 Front Load...

1 Answer

My maytag home top loading washing machine over fills with water, ie. the switch to stop filling and start washing doesn't go off. I can drain it by setting it to spin.

top loading machines comes with a pressire switch to determine the water level.IT will fill with water till the switch is triggered to stop filling and continue with the next task of washing. there would be a rubber hose connected from the wash bucket to the pressure switch. Check for broken,leaking,bitten by rats hose or probably the switch it self is faulty, which is rather rare.

Aug 24, 2011 | Washing Machines

1 Answer

While moving my samsung top washing machine, I think my drain hose pipe has moved down the water level. Now machine is not able to retain the water while washing/soaking. I need to pull the drain hose pipe...

Hi,

Although a few modern washing machines can operate with the drain pipe at any height, most machines will drain the water as soon as the drain pipe is placed below the machine water level.

The simplest solution for your problem would be to ask somebody with some handy man skills or hire a plumber to add a 2 inch PVC pipe to your drainage pipe which extends to a point behind your washing machine & then points upwards, making sure it is long enough to be at a higher point than your machines fullest water level.
This should be a relatively inexpensive alteration & will ensure that water does not drain unless the machine is on its drain cycle.

Please let me know if you need any further assistance.
Best wishes,
Graeme

Mar 10, 2011 | Samsung SW62ASP Top Load Washer

1 Answer

I put a fairly large load in washer. As the washing started I needed to add an item. I was surprised that the machine had very little water in it. Is there a way to add more water. Also when soaking I had...

The Series 10 and 11 machines have three level fill points the Series 12 and above have two level fill points.

I know Bulky Items wash selection will give you a High water fill which is only 7 inches or so of water in the wash basket. 3.5 inches of water for a medium fill.

You can turn on/open the water inlet valves in Service Mode but I would not recommend that. A manual fill as you did is the only safe way to set the additional water level IMOP.

FAV6800A/FAV9800A Service Manual for reference.

Rich

Jul 05, 2010 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

MACHINE MAKES DOES NOT WASH,WATER OUT FROM DRAINAGE PIPE

is it a top or front loader?is your drain hose same level as top of machine?if not ,raise hose to level and start cycle.machine will not wash if it does not fill.please reply if u need more help

Apr 05, 2010 | LG Washing Machines

1 Answer

Mold growing

If you mean on the outside of the machine, there is probably a slow water leak, and it is soaking the floor which is making to much moisture.

If your talking inside the machine.

Try and wash by hand the machine with a 50/50 bleach/water/ and a 1/4
cup dish detergent.

Run the machine through a full wash cycle, with a 1/2 gallon bleach
in a small load setting,

Then run the machine with full load setting and nothing for detergent, just the water, say three times. To flush all the cleaning you did away.

From now on leave the door open when done so if there is any water or moisture inside it does not stagnate.

Feb 08, 2010 | Frigidaire GLTF2940ES Front Load Washer

1 Answer

Water is pooling in the front of the top loading washing machine

Hi,

If I got the issue correct the washing machine is leaking specially from the in front of your top loading washing machine.

Leaking water from a washing machine usually comes from hoses or connections. Be sure that water appearing to be a leak isn’t drain water from a backed-up standpipe. To prevent potential flood damage, which can occur if washing machine supply hoses burst, be sure to install “no-burst” stainless-steel mesh hoses and lever-type shutoff valves, as shown below. With these, you can easily turn off the levers for both hot and cold water between wash days.

1) Check the fittings where the hoses connect to the faucets and to the back of the washing machine. Also look for worn or leaky hoses. Tighten couplings or hose clamps if needed, or replace the hoses altogether. Be sure to turn the water off before removing the hoses, and drain them into a bucket after disconnecting them.

2) Determine whether the machine is overwashing, which can cause the machine to overflow. Reduce suds by pouring 1/2 cup white vinegar in 1 quart water into the washer. Then switch to either less detergent or a low-washing variety.

3) The machine may have a faulty basket gasket or tub seal and bearing that must be replaced; in this case, call an appliance repair person.

Thank You for contacting fixya.com

Oct 12, 2009 | Whirlpool Ultimate Care II LSQ9564J Top...

1 Answer

When the wash is finished it doesnt drain the

Make sure that there is no blockage in the drain hose and that it is not kinked. Is the drain hose installed correctly? If you have connected your machine to a sink waste system, make sure that you have cut out the membrane from the under sink drainage system.
Ensure that the drainage system, standpipe or under sink connection is free from any blockage. - If any of the above are found to be the cause of your problem you will need to run the machine through a spin only programme. If you have chosen ‘Rinse Hold’, the light will flash until you press the ‘Rinse Hold’ button to continue the programme.

Jul 18, 2009 | Hotpoint Aquarius WMA42 Front Load Washer

1 Answer

Black marks on clothes

I had a similar problem. We has placed the waste water hose into an old tub next the machine. The plug hole int he sink has become blocked with lint. When the washing maching was pumping water into the tub, the tub would fill with water, which would rise a level higher than the washing machine waste hose. What this appeared to do was cause the machine not to be able to properly pump out water, leaving this horrible back stuff in the wash which would end up all over the wash. Ensuring the plub hole in the tub was clear solved the problem immediately!

Mar 01, 2009 | Fisher Paykel EcoSmart GWL15