Address for repair place

In the event that you don't approach the Canon printer or on the off chance that you would prefer not to look through the menu framework, discover the canon printer IP address on any PC on which the printer is set up.

FOR WINDOWS

Open Control Panel > Devices and Printers. Right-click the printer and select Properties.

One of two arrangements of tabs shows, contingent upon the kind of association the canon printer driver employments. In the event that the Canon printer is set up under a WSD port, it uses Web Services for Devices innovation to associate with the printer. For this situation, select the Web Services tab to see the printer IP address recorded in the IP address field.

On the off chance that you don't see a Web Services tab, at that point the Canon printer is set up utilizing a TCP/IP port. For this situation, discover the IP address in Printer Properties.

1. In Control Panel, pick Devices and Printers.

2. Right-click the printer and select Properties.

3. Select the Ports tab. The IP address is shown in the Port field.
Port tab of printer Properties with IP address

4. On the off chance that you don't see the IP address, select Configure Port to see the IP address arranged for that printer.

Try manually locating ip address to your laptop Right click on the local area connection icon and then click on Status, click on the properties this will help you to be able to Change the Local Area Connection Properties, Click on the Internet Protocol(TCP/IP) Click the properties button under then click on use this IP address provide the required IP address, Subnet mask and Default gateway and also click on use this DNS server address and then fill the field as necessary after try repairing the Local Area Connection.

Hi, Please get your driver here, select your country first before do next step : http://www.canon.com/products/office.html
Other reference website for your canon is here : http://www.freedownloadsarchive.com/c-download/canon-ir-400-copier-user-manual.html

Regars, vote please, Jay

Find your computer's IP address : Windows 7, Vista, and XP, using the command prompt

1. Click Start, and then select All Programs. Note: If this doesn't match what you see, refer to About navigation settings in Windows.
   
2. Click Accessories, and then Command Prompt.
   
   
3. At the command prompt, enter: ipconfig The IP address (or IPv4 address, if you are using Windows 7 or Vista) will be a series of numbers following the pattern xxx.xxx.xxx.xxx (i.e., 156.56.27.32).
   

Note: If you are using PPP with a modem at home, your IP address will change each time you log in.
Windows 7, without using the command prompt

1. In the system tray, click the network connection icon and select Open Network and Sharing Center.
   
   
2. To view the IP address of a wired connection, click Local Area Connection. To view the IP address of a wireless adapter, click Wireless Network Connection (Network Name).
   
3. Click Details... . Your IP address will appear next to "IPv4 Address".

Windows Vista, without using the command prompt

1. From the Start menu, right-click Network, and then select Properties. This opens the Network and Sharing Center.
   
   
2. To view the IP address of a wired connection, click View Status to the right of Local Area Connection. To view the IP address of a wireless adapter, click View Status to the right of Wireless Network Connection.
   
3. Click Details... . Look for the address next to "IPv4 IP Address".

Windows XP, without using the command prompt

1. From the Start menu, right-click My Network Places, and then click Properties.
   
   
2. To view the IP address of a wired connection, double-click Local Area Connection. To view the IP address of a wireless adapter, double-click Wireless Network Connection.
   
3. Click the Support tab, and then click Details... . The window that appears will display the IP address.

Your IP address has to be in the 192.168.123.xxx range

The router must be configured to match your

Internet service. If you do not know your

Internet connection configuration, please

contact your Internet Service Provider (ISP).

By default, the router is pre-configured with

these settings:

• Automatically set IP addresses for

computers on your LAN (connected to the

router's ports 1-4). The router acts as a

server for dynamic host configuration

protocol (DHCP) and assigns IP addresses

in the range 192.168.123.100 through

192.168.123.199

• The default LAN IP address for the router is

192.168.123.254 with a subnet mask of

255.255.255.0

• The Internet service connected to the
router's WAN port uses a dynamic IP

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response. Happy Holidays!

Thanks, Joe



I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

Windows XP

1. Verify Ethernet adapter in device manger.
   
   1. Click Start > Search > Type in ncpa.cpl and press Enter.
   2. Click System>Hardware > Device Manager
   3. Click Network Adapters
   4. Verify adapter present, enabled, and no error messages.
   5. If error reported refer to OEM regarding error receiving
2. Open the Network Connections window.
   1. Click on Start > Run > Type in ncpa.cpl and click OK.
3. Double-click on the Local Area Connection icon.
4. Click the Support tab.
   1. Ensure that Address Type: says "Assigned by DHCP."
   2. Ensure that the IP address is valid.
   3. If both are correct, click the Repair button and then skip to Step 9.
5. If it does not say "Assigned by DHCP" click the General tab and then click Properties.
6. Select "Internet Protocol TCP/IP" and then click on the Properties button.
7. Ensure that the radio buttons are marked as "Obtain an IP Address automatically" and "Obtain a DNS Server address automatically" and click OK.
8. Click OK again to close out of the Local Area Connection properties.
   1. Restart the system if any changes were made to the configurations.
9. Right-click on Local Area Connection and select Repair.
10. If the repair fails because the system is unable to flush the ARP Cache, the Routing and Remote Access service will need to be stopped and set to disabled.
    1. Click Start>Run>Type services.msc >Click OK.
    2. Double-click on Routing and Remote Access.
    3. Click the Stop button.
    4. Set Startup Type to Disabled and click Apply, then OK.
    5. Restart system.
11. If the Repair fails to renew the IP address, ensure that all firewalls are disabled and try again.
12. If it still fails, reset the networking protocols.
    1. Click Start>Run>Type CMD and click OK.
    2. Type netsh int ip reset reset.log and press Enter.
    3. Type netsh int ip delete arpcache and press Enter.
    4. Type netsh winsock reset and press Enter. (SP 2 or later)
    5. Type ipconfig /flushdns and press Enter.
    6. Restart the system.

Windows Vista

1. Verify Ethernet adapter in device manger.
   
   1. Click Start > Search > Type in ncpa.cpl and press Enter.
   2. Click Hardware and Sound > Device Manager
   3. Click Network Adapters
   4. Verify adapter present, enabled, and no error messages.
   5. If error reported refer to OEM regarding error receiving
2. Open the manage Network Connections window.
   1. Click Start > Search > Type in ncpa.cpl and press Enter.
3. Right-click on Local Area Connection and select Properties.
4. Uncheck Internet Protocol Version 6 (TCP/IPv6).
5. Select "Internet Protocol Version 4 (TCP/IPv4)" and then click on the Properties button. (Do Not Uncheck Version 4).
6. Ensure that the radio buttons are marked as "Obtain an IP Address automatically" and "Obtain a DNS Server address automatically" and click OK.
7. Click OK again to close out of the Local Area Connection properties.
   1. Restart the system if any changes were made to the configurations, including unchecking TCP/IPv6.
8. Right-click on Local Area Connection and select Diagnose.
9. If Diagnose fails to renew the IP address, ensure that all firewalls are disabled and try again.
10. If it fails again, choose to "Reset the Network Adapter."
11. If it still fails, reset the networking protocols.
    1. Click Start>All Programs>Accessories.
    2. Right-click on Command Prompt and select "Run As Administrator"
    3. Type netsh int ip reset reset.log and press Enter.
    4. Type netsh int ip delete arpcache and press Enter.
    5. Type netsh winsock reset and press Enter.
    6. Type ipconfig /flushdns and press Enter.
    7. Restart the system.

Windows 7

1. Verify Ethernet adapter in device manger.
   
   1. Click Start > Search > Type in ncpa.cpl and press Enter.
   2. Click Hardware and Sound > Device Manager
   3. Click Network Adapters
   4. Verify adapter present, enabled, and no error messages.
   5. If error reported refer to OEM regarding error receiving
2. Open the manage Network Connections window.
   1. Click Start > Search > Type in ncpa.cpl and press Enter.
3. Right-click on Local Area Connection and select Properties.
4. Uncheck Internet Protocol Version 6 (TCP/IPv6).
5. Select "Internet Protocol Version 4 (TCP/IPv4)" and then click on the Properties button. (Do Not Uncheck Version 4).
6. Ensure that the radio buttons are marked as "Obtain an IP Address automatically" and "Obtain a DNS Server address automatically" and click OK.
7. Click OK again to close out of the Local Area Connection properties.
   1. Restart the system if any changes were made to the configurations, including unchecking TCP/IPv6.
8. Right-click on Local Area Connection and select Diagnose.
9. If Diagnose fails to renew the IP address, ensure that all firewalls are disabled and try again.
10. If it fails again, choose to "Reset the Network Adapter."
11. If it still fails, reset the networking protocols.
    1. Click Start>All Programs>Accessories.
    2. Right-click on Command Prompt and select "Run As Administrator"
    3. Type netsh int ip reset reset.log and press Enter.
    4. Type netsh int ip delete arpcache and press Enter.
    5. Type netsh winsock reset and press Enter.
    6. Type ipconfig /flushdns and press Enter.
    7. Restart the system.

I hope this helps

refer to http://www.samsung.com/in/support/location/serviceLocation.do?page=SERVICE.LOCATION to help find your local Service Centre.

I am not sure but I believe the IP address is not correct. The trace goes to the following address:

Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Tracing route to 200-100-1-5.dsl.telesp.net.br [200.100.1.5]

on my machine. This is only a service provider I believe and not an end website. Have you checked and verified the ip address with the contact organization? Just because you can run a trace route on an ip address does not make accessible.

The cisco could also be blocking the outbound connection at your end.

Hope this helps.

Print the config page, is the easiest way -Carl

connect your router your computer via LAN cable
click start on windows
click run and type CMD
On the DOS command prompt type IPCONFIG/ALL
look for the gateway address, that is the IP Adress of your router

Most likely you will have to log into the machines interface by putting the machines IP address in your web browser. Once there you will have to put the new email settings in the machine so it can email properly.