Question about Dishwashers

1 Answer

Indesit DIF04 integrated dishwasher

Hi, I have just bought a Indesit DIF04 UK integrated dishwasher, we have not recieved it yet but are wanting to get the plumbing part sorted before it arrives. Could you please advise if this dishwasher is a cold feed only or if it uses a hot and cold water feed?

Thanks
Serena Munro

Posted by on

  • Anonymous Mar 22, 2014

    will not start

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 549 Answers

Dishwashers normally are hot or cold feed.
My wife runs water at the sink to get it hot going in before turning on the dishwasher.
You can use either cold or hot water.
We have ours hooked up to the hot water side.
They work better hooked up to the hot water.

Posted on Mar 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Flashing lights indesit dishwasher


Please refer this post

http://www.justanswer.com/uk-appliance/6tq6a-indesit-idf125-wash-end-lights-flashing-turn-maching-on.html

looks like some sort of heater problem. I don't think I can add anymore to the solution than what is mentioned there.
The parts are listed on this site
http://parts.indesit.co.uk/shop/spare-parts/dishwashers/idf125-uk/p/F060257?q=:category_highlight

Apr 24, 2014 | Dishwashers

1 Answer

My dishwasher is not pumping water through the arms. The plates are coming out dirty. The dishwasher does drain and it does fill OK. What can we do, we have had the dishwasher 2.5 years really do not want...


It is possible that the machine does not start off the cycle because there are errors or back feedback from the inputs. For the program to start up the main program controller must initiate the INLET valve to open up and allow water to flow into. If the water flows then the flow should be good, if not the inlet valve is bad or there is dirt in the filter. Also check the flow at the inlet of the water line. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor .

The LOW PRESSURE ON THE PUMP CAN BE THE REASON FOR POOR WASHING. so check the pump , it canbe faulty - clogged with dirt, if so remove and clean.

Finally after the wash the drain valve will be activated, the water is allowed to come in to rinse and then finally the drain valve/pump activated so as to drain off all the water .

Make sure that a fault in any of the cycle will relate to the specified action, so check the command from the program module and then the executing device be it the valve or motor or pump.

Please check the link below:

http://www.espares.co.uk/advice/dishwashers/a/3

For spares click On:

http://www.espares.co.uk/search/dishwashers/p/1083

Jul 23, 2011 | Dishwashers

1 Answer

Indesit Model DIF04 UK.R rear Levelling Foot Does Not Turn


well does it look the same as the front ones??....I would say so...squirt some wd40 up into the threads and leave overnight....try again next day it may just have seized up.

Jul 27, 2010 | Dishwashers

1 Answer

Indesit dishwasher wont come on


this might be a little late but i ahve the same problem, an indesit engineer has been and there ia a metal bar the control wires rub against when opening/shutting the door. major design fault if you ask me. it tripped my entire kitchen and extention out.

May 05, 2010 | Dishwashers

2 Answers

Indesit IDL40 Dishwasher


from indesit website http://www.indesit.co.uk/indesit/_pdf/manuals/19504287203_UK.pdf

Mar 25, 2009 | Indesit 18 in. D41 Slim-Line Free-standing...

1 Answer

Dishes not clean and leaks sometimes


Hi,


I have an older dishwasher also and recently my wife also complained about it not cleaning right... so me being the man I am tried in vain to clean the things... Bought new spray arms online and installed them in minutes...now the thing works like new... However I have also found that if the heating element goes bad then that also can mess things up bad... So I would buy new spray arms, and also check out the heating element to make sure it is working... Here is a tip that will help you with the online buying...

Dishwasher Spray Arms not Spinning

How to Buy Appliance Parts Online

A bad heating element causes many problems in dishwashers...

Dishwasher Problems The Heating Element not Working

Dishwasher Maintenance

heatman101

Feb 03, 2009 | Indesit 23 in. DV62 IX Built-in Dishwasher

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

758 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Are you a Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...