Question about Audio & Video Receivers

3 Answers

TEAC GF-650 Using the AUX Input jacks, cannot record cassettes and pre-recorded cds. The recording modes look normal, but when I listen to the newly burned cd, there's no sound. I'm using the correct blank cds, so that's not the problem (CD-R digital audio recordable). The instructions for using AUX is very, very brief. I need more step-by-step instructions. Do I need a cables for AUX OUT too? Thanks! Connie Hooper cshooper@pacbell.net

Posted by on

  • 2 more comments 
  • cshooper Mar 22, 2008

    Is this the same manual that I received with the stereo system? Thanks!

  • cshooper Mar 22, 2008

    That was no help! I don't have a GF-180!

  • cshooper Mar 27, 2008

    With my TEAC GF-650, I cannot record from tapes and other cds from my older stereo system to the AUX mode of the TEAC system. Everything that I can see shows that the TEAC is recording, but when I listen to my cds (after finalizing) I hear nothing. The instructions are unclear about recording from the AUX mode. Do you have any suggestions as to why it isn't working? The TEAC does record LPS with no problems. What am I doing wrong? Thank you!

  • cshooper Mar 28, 2008

    Hi!

    I have an old (early 90's) Yamaha YST-C10 stereo system with "Active Servo Technology". It consists of AM/FM radio, CD player and dual cassette player/recorder. It may be old, but still plays great! It has only AUX inputs. Consumer Reports rated it the best of compact stereos at the time. I hope you can help! Thanks!

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,944 Answers

Hi,

What is the source of your audio?

Posted on Mar 27, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,665 Answers

If you have not any solution you can buy a service manual at link below:
http://www.user-manuals.com/service-manual-TEAC-GF650.html
It gives a lot of information at low cost.
good luck!

Posted on Mar 20, 2008

  • Kleanthis Mavropoulos
    Kleanthis Mavropoulos Mar 29, 2008

    I suggest to download the service manual where only can find a circuit diagram to troubleshoot the input source selector.

    If you can have access to input selector it would be usefull to inspect it's contacts condition and have them well cleaned.

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 377 Answers

AUX directly to computer? no need...

Posted on Mar 20, 2008

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Connect to PC


You can use the audio our port to be connected to the audio input - MIC input- which can be selected as the AUX input. Select audio properties and select and switch the input to AUX so that the input is reduced to match the signal.Hence the audio outputs from receiver can be connected to this input and it can also be recorded by using the default recorder or the Sound Forge which can be downloaded.

Dec 17, 2011 | Sony STR-V555ES Receiver

1 Answer

I have a Technics Double Cassette Deck RS-TR212. On the rear it has Output and Input connections. Output goes off to the Amplifier. Can the Input be used to record or play from a record Turntable? I have...


your receiver has (or should have) input and output connections,, your turntable needs to be hooked to the receiver,, then with the output cables that feed your cassette player you need to go, in to out and out to in ( receiver output to the input of the tape player, and out of the tape player to the in on the receiver, while playing a record if you hit record on the tape player it will record the record, depending on the receiver it will show you the meter readings for either the in or out,, they vary

Apr 11, 2011 | Audio & Video Receivers

1 Answer

Can i play records through my sherwood rd6108 receiver? When i try to play a record i get no sound no matter which channel i use.


Record players require a PHONO input on an amp.
Most amps no longer have this, so you will need to source out a pre-amp for the record player, and then you can plug the record player into the pre-amp and then hook the pre-amp into a tape, DVD or AUX input.

Feb 27, 2011 | Audio & Video Receivers

1 Answer

How to connect a record player to Pioneer


If there are no specific phono inputs, then a phono pre-amp must be purchased. These usually cost around $20. This pre-amp will boost the signal level to that of a CD player or tape deck so that either a tape input or aux input can be used. Once you have the pre-amp, just connect its output to an open input on the receiver.

Dan

Jan 12, 2010 | Audio & Video Receivers

1 Answer

Output from Denon D-700?


Hi ...

If there's a tape monitor in/out on the D700,turn the tape monitor on and connect the "Play out" phono jacks on the 700 to the line-in on the computer. Spark up the turntable and you should be able to listen to the vinyl on the PC while recording.

Nov 21, 2008 | Denon AVR-1803 Receiver

1 Answer

No sound from my record turntable into my computer.


If you're certain there is no sound going out of the TT...

Setting the Pre-amp Switch
For increased flexibility of use, this turntable has an internal
stereo phono pre-amplifier. The Pre-amp Selector Switch
is located under the turntable platter, in the rear-center
(Fig. 1). If the system amplifier you are using has a PHONO
input, set the Pre-amp Selector Switch to the “OFF”
position. If your amplifier does not have a PHONO input,
set the Pre-amp Selector Switch to the “ON” position and
connect the turntable’s output cables to the AUX or other
high-level input on the amplifier (described later).

Turntable operates, but no sound at all
1. The stylus guard is still in place.
2. The tone arm Lift button is pressed in.
3. Amplifier controls set incorrectly: wrong input selected,
tape monitor on, speakers switched off, etc.
4. Check the stylus on phono cartridge for correct placement.
Refer to the instructions for replacing the stylus
on page 5.
Turntable operates, but no sound, or sound not loud
enough
1. If the turntable is connected to an AUX (high-level)
input: The Pre-amp Selector Switch may be set to the
“OFF” position (phono-input level).
2. The input gain of the amplified speaker or similar
device may be too low.
3. The stylus assembly may not be fully seated in the
cartridge body.

You could also isolate the problem to either the TT or the PC by trying the TT on some other sound device like a receiver. Make sure the PreAmp Selector switch is ON and plug the TT into any AUX, CD or TAPE input.

Sep 02, 2008 | Nakamichi AV-7 Receiver

1 Answer

Teac Cassette Deck V-518X. No Record Audio.


Hello,

Found a pinched wire under the cassette deck from the record head. Move the wire out from under the cassette deck. Works fine!

Thanks!

JOHN

:)

Aug 05, 2008 | Teac Audio & Video Receivers

1 Answer

Kenwood KA-72B Stereo Receiver HELP NEEDED.


Why not plug the cassette directly into the CD recorder? Are they trying to achieve some eqalization change? If not, then this should work. It's all analog at tape level.

Mar 02, 2008 | Audio & Video Receivers

2 Answers

Teac rw-cd22 burning problem


You were right! I changed the cd and it does not do DA:D2

Feb 13, 2008 | Audio & Video Receivers

1 Answer

Volume turned to MAX for almost no sound from record player


You will need to purchase small box that converts your phono magnetic cartridge level output to a higher line input level before it goes into the TV input jack. Radio Shack used to sell a small amp for about $20 that was made just for that purpose and was called a stereo pre-amplifier and was model number SPA-50 and it plugged into the standard wall outlet to get power. Back in the "old" days when phono magnetic cartridges first became popular some of the older home stereos had only the ceramic phono style inputs (or an aux. input) which were about the same input level as a tape input or aux. input (or TV input) and so you would have to use one of these adapters to boost the newer magnetic cartridge signal up to the same level as a ceramic cartridge in order to use a new style of phono. This will fix your problem if you can find one at Radio Shack or some other place, perhaps on the internet. Hope this helps you.

Nov 20, 2007 | Sony STR-DG510 Receiver

Not finding what you are looking for?
Audio & Video Receivers Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio & Video Receivers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

The Knight
The Knight

Level 3 Expert

68223 Answers

yadayada
yadayada

Level 3 Expert

60792 Answers

Are you an Audio and Video Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...