Question about Lands Phones

1 Answer

Upload aastra config to router

Edgewater 4500

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 807 Answers

The only thing I can find for that model is this manual.
ftp://ftp.edgewaternetworks.com/pub/docs/EdgeMarc/4500/4500%20Series%20Hardware%20Installation%20Guide.pdf
but it does'nt mention anything about Aastra.

Posted on Mar 21, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i cable 10 computers, a docsis 3.0 modem, 8 port edgewater 881 router and 5 port trendnet TEG-S5G unmanaged switch


Connect 7 computers to the 881 router. The last port on the 881 router go to Trendnet switch. Connect the last 3 computers to the Trendnet.

Feb 11, 2013 | Computers & Internet

1 Answer

Slow upload speed


It is usual that the internet speed differs when connected to a modem and a router. You have many possibilities to get signal affected while connected through a router.
Anyway you can try with these basic steps to get a better connection through router,
1.) Reset the wireless router by using the power switch on it or by unplugging it and plugging it back in.
2.)Place the wireless router in an ideal location. The higher it is, the better, but don't put it near metal objects.
3.)Get as close as possible to the router with whatever device you're trying to connect.
4.)Keep the router and your connecting device away from other electronics. You should especially keep away from phones, fax machines and microwaves. etc.,
5.)Adjust the Wifi antenna if it has one.
6.)Change the router's channel, especially if other wireless routers are nearby.
Following these steps would give you stable internet connection and also increased speed in connection. You can check your internet speed from www.ScanMySpeed.com before and after performing these steps.

Sep 12, 2012 | D-Link DGL-4500 Wireless Router

1 Answer

1840 cisco router is not booting only cursor blinking not going ahead


HI,
It May be the problem with the IOS in the router Flash
  • Try hard reboot of the router If it is not soled proceed next.
  • while the router reboot press Pause button continuously, it will enter into the ROMMON mode.
  • using the Xmodem option upload the correct IOS, for refer Please refer the link
  • Please check the configuration Loading by confreg or config-register command and change into confreg 0x2142 to load from the Flash and reboot the router.

Jan 20, 2011 | Cisco (1841) Router (cisco1841)

3 Answers

How do I open ports 500, 4500, 53, and 52428 on Dell TrueMobile 2300 wireless router. Need to open them for Verizon Network Extender


1.Open the router interface by checking the default gateway
2.Under FIREWALL, you can find an option that would say "Virtual Servers"
3.Enable these ports, along with their types(TCP/UDP/Both) and assign an IP address that your Verizon Network Extender is going get( you to set that manually on the verizon device)
Save the changes and the ports will get forwarded!
**Note: In this case, DMZ under FIREWALL will NOT work!

Jan 18, 2010 | Dell Wireless 2350 Router

1 Answer

I have a siemans gigaset se587 and i need to enable access to UDP 500 and UDP 4500. How do I do this?


You need to access your unit via it's web interface and go to the Firewall config. UDP is a one way protocol that needs to be able to operate, based on your information, through ports 500 and 4500. You should by default have this open on your LAN. If you need UDP access through the firewall to the WAN, you can allow those entries through the firewall. The manual should be able to walk you through this. Depending on what you are doing, you might need to open those ports on your computer also.

Oct 19, 2009 | Computers & Internet

1 Answer

Dlink 4500 router want download newest firmware


You can go to http://www.dlink.com/ and search for you routers model #. The model # is probably going to start with DI-xxxxx . You can then download the firmware and then upload to the router from you computer.

Mar 09, 2009 | Computers & Internet

1 Answer

Astra config file to router


Which router is it, make and model.

Mar 13, 2008 | Lands Phones

1 Answer

Software



http://www.dynexproducts.com/t-customer_support.aspx

Enter DX-E401 into Search and Click GO

Click this link under Product Matches
Dynex 4 Port Ethernet Broadband Router

You now have links to manuals, firmware and FAQs.

There is firmware that can be uploaded to the router and the FAQ and Manuals will explain the configuration process

Dec 16, 2007 | Dynex DX-E401 Router

Not finding what you are looking for?
Lands Phones Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lands Phones Experts

kakima

Level 3 Expert

102366 Answers

Cindy Wells

Level 3 Expert

4945 Answers

yadayada
yadayada

Level 3 Expert

70346 Answers

Are you a Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...