Question about Car Audio & Video

3 Answers

My peugeot 206 center consul radio display is so dull i cant read it..its very faint but at a certain angle i can see it so it still working please

Posted by on

  • oliversband Mar 25, 2009

    i have same prob m8, it doesn't look asif its on. but at an angle u can still see it faintly.

    i had all new fuses and bulbs put in it, still the same tho :(.


3 Answers

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 2 Answers

Bit late but...
Its a poor connection between the pins that suplly power to the bulbs and the circut board.
Take the whole section apart, take the circuit board off the white plastic holder and solder 'blobs on the connections on the board, above and below the locating holes.
stick it back together and should stay lit now!

Posted on Feb 20, 2010

Replace the bulbs then

Posted on Oct 26, 2008


Posted on Mar 22, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Time on car radio display

With the ignition key in position 1 or
higher, you can use the button in the
turn signal lever to request information
from the computer. Each time you
press the button briefly toward the
steering column, a new function is
called up in the display.
The displays appear in the following
Time of day, outside temperature, average
fuel consumption, cruising range,
average vehicle speed.
With the ignition key in position 1 or
higher, the last active setting is displayed.
press the button you mentioned when the
time of day displays and turn to right to set
ahead left to set back

Nov 18, 2007 | Car Audio & Video

1 Answer

Peugeot 206 stereo says locked

It says LOCKED because wrong codes have been entered previously

To reset , leave SWITCHED ON...UNDISTURBED for as long as it takes to automatically reset itself

This may take an hour or more

Make sure you have the correct code

Apr 21, 2011 | Blaupunkt Car Audio & Video

1 Answer

My kvt-719dvd will not power up. I hit the reset button and nothing happens. When I take the faceplate off the red security light blinks....Just wired up a flip down and using the same power source as the...

take a digital volt meter and check powers and grounds

red ignition switched wire should read with car on and running 12.5 volts to 14.4
yellow constant power comming from battery should read at all time 12.5 to 14.4
black wire is ground and should be ground to the frame of car

lets take your radio ground and put your volt meter black lead on it and then put the red test lead to the read wire and if you have a good ground you get a reading of 12.5 to 14.4 if you car is running if ignition if on accesory it will read 12.5 do the same test to the yellow wire make sure you get a reading without the car on at all . this wire will have power on all the time hint(constant power) or (b+) if no reading on any wires you have a bad ground

let me know what you get for voltage to help you more

to get a good ground you need to scrap the paint off to bare metal and then us a stare washer and use a good stanless steal screw so dont rust for a good ground ..

Oct 14, 2010 | Kenwood KVT-719DVD 7 in. Car Monitor

2 Answers

How do i fix my peugeot 206 led radio/cd display it has gone completely black. a real problem when you try and tune your radio. Stephen.

Its a poor connection between the pins that supply power to the bulbs and the circuit board, take the unit apart and you'll see the pins, Make the connection better by soldering blobs on the pins and this should keep the bulbs lit.

Apr 29, 2009 | Car Audio & Video

1 Answer

On/off button

Copy and paste this link in to your web browsers search bar.

Mar 22, 2009 | Car Audio & Video

1 Answer



Aug 14, 2008 | Car Audio & Video

1 Answer

The digal read out on the dash of a 1988 bmw 735iL

there have a "setup" manu, and choice the langue, and enter the osd langue to english is ok...

Feb 16, 2008 | Car Audio & Video

1 Answer

LCD screen in speedometer of 1989 Ford LTD ( car )is too faint to read

Only by fitting brighter backlight, but this is normally not that easy, depending on the size. Some backlights are part of the LCD assembly, on smaller units they are sometimes side mounted. The contrast on an LCD is usually adjustable - there may be a small potentiometer on it that will adjust the contrast, that may improve matters.

Jan 13, 2008 | Car Audio & Video

1 Answer

HELP ME!!!!!


Dec 19, 2007 | Car Audio & Video

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

2,149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Car Audio & Video Experts

xxxxxx xxx

Level 3 Expert

4724 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers


Level 3 Expert

63291 Answers

Are you a Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides