Question about Back to Basics 600 Smoothie Plus Work Top Blender

1 Answer

Back to Basics Smoothie Plus 600 Spout

The Spout that dispenses the smoothie from the pitcher is broken. How can I obtain a replacement?

Posted by on

  • 1 more comment 
  • Anonymous May 24, 2008

    The flip part of my spout broke off and there is no way to dispense the smoothie now. Please help as we use this smoothie maker a great deal.

  • Anonymous May 24, 2008

    The spout on my smoothie blender Pro 600 snapped off. We need a new spout.

  • Phoebe Trotter Jun 19, 2013

    I need a pitcher with dispensing spout replacer for the Smoothie Duo, Item # 147397, Model #SA2500.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 114 Answers

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacement pitcher


The Manufacture, Back to Basics was bought out by West Bend. They have since discontinued these smoothie makers, and unfortunately all of the parts for the Back to Basics Smoothie Pro 700.

Dec 10, 2013 | Back to Basics 700 Smoothie Pro Work Top...

1 Answer

I took the spout of the smoothie plus 600 apart and can't put it back together


When you say you took the spout apart and can\'t put it back together its only 5 total pieces. The spout, the spring, the handle, the dispenser (rubber insert with plastic stem) and the threaded cap which holds the dispenser and handle to the spout.

If you can\'t get the handle to re attach, that does not surprise me. This is very poor craftsmanship. The plastic nobs that hold the handle onto the dispenser tend to break off.

If this is your problem, you can either, buy a new one for $5 plus shipping depending on where you live OR

You can fix the part that broke.

All you would need is a Drill, a small piece of number 14 copper about an inch long and same size drill bit. Drill the handle as close to center where the plastic molded nobs were located that either broke off or worn away. Then drill with the same size drill the stem to the dispenser which has the rubber stop attached. Drill this as close to the top of the stem where the nobs would snap in to hold the handle in place. You are basically making a pined handle, which will outlast the quality of this blender.

NOTE: You want to use a drill bit about the same size as the number 14 copper wire.

Then with one hand hold the threaded cap with the dispenser placed into position through the hole, be sure to put the spring in, small hole to the bottom of the rubber dispenser, pushing the spring and dispenser up through the threaded cap, attach the handle by putting the piece of copper wire in your hole which will connect your handle to the stem of the stopper. The copper should be cut no wider thent the width of the handle, if it sticks out a tiny bit, that\'s ok. The plastic cap will simply be carved out where the copper rubs against it. After that, simply screw the handle cap back onto the spout and screw the spout back onto the blender making sure the two washers are still on the pitcher.

All in all, for someone who is handy, this should take about 10 minutes. I would rate it about a 5 out of ten for difficulty simply because you have to drill straight and centered in the handle where the nobs were. Other then that its easy and if you can have someone help you put the pin in place, it would also make it easier.

If for some reason the rubber stop does not seem to go back into the spout, make sure the rubber didn\'t role up onto itself. Also if the spout drips, you didn\'t either put the spring back in or you didn\'t drill at the top of the plastic stem but some where in the middle, simply ream the hold towards the top where the plastic nobs would stop. Its a square reseated area in the stem. Looking at it you should be able to tell.

As for the spout instructions, you can download the pdf manual at the manufactures website: http://westbend.com/spl6white-smoothie-maker-plus-600.html

Hope it all helps, Its worked for me!

Dec 31, 2012 | Back to Basics 600 Smoothie Plus Work Top...

1 Answer

I need a replacement pitcher for a back to basics smoothie elite se2000. Do you have any?


You can order replacement parts for your smoothie maker online from the following site:

http://www.westbend.com/catalog.cfm?dest=itempg&itemid=3694&secid=87&linkon=subcategory&linkid=90

Your pitcher may be currently out of stock so you may have to wait or send them an e-mail to see if you can be put on back order.

Aug 02, 2011 | Back to Basics Smoothie Elite Work Top...

1 Answer

Smoothie pro 600


When you find out how to contact Back To Basics you let me know. They don't seem to exist except to rip you off when you buy their junk

Jan 15, 2010 | Back to Basics 600 Smoothie Plus Work Top...

1 Answer

The pour spout on my Back to Basics Smoothie Freeze has completely cracked off. Where do I get a new container with valve and pour spout?


I am looking for the dispensing valve for my BackToBasic. I'm not sure but I think it is a 700. It is a black dispenser with a chrome base. Please let me know if this part can be replaced. I could settle for a white one but it would look like a "saddle on a donkey" as my husband would put it.

Jul 06, 2009 | Back to Basics 600 Smoothie Plus Work Top...

Not finding what you are looking for?
Back to Basics 600 Smoothie Plus Work Top Blender Logo

Related Topics:

6,553 people viewed this question

Ask a Question

Usually answered in minutes!

Top Back to Basics Blenders Experts

Cindy Wells

Level 3 Expert

4989 Answers

Mike Neath
Mike Neath

Level 3 Expert

315 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Back to Basics Blender Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...