Error message says please check upper thread. I do that and then it stops after a few stitches. Please Help. Carolyn

If your Babylock EMP6 embroidery machine starts stitching a design and then stops, displaying a message to check the upper or bobbin thread, there are a few potential causes for this issue:

1. Thread tension: Improper thread tension can cause stitching issues. Ensure that both the upper and bobbin threads are properly threaded and the tension settings are adjusted correctly. Check the machine's manual for specific instructions on setting the thread tension.
2. Thread breakage: Check both the upper and bobbin threads for any signs of breakage or tangles. A broken or tangled thread can cause the machine to stop and display the error message. If you find any issues, rethread the machine and ensure the threads are properly seated in the tension discs and bobbin case.
3. Bobbin issues: Check the bobbin area for any obstructions, such as lint or tangled thread. Clean the bobbin case and ensure the bobbin is correctly inserted and spinning freely. If the bobbin is wound unevenly or has any defects, replace it with a new one.
4. Needle issues: A bent or dull needle can cause stitching problems. Check the needle for any damage and replace it if necessary. Make sure you are using the correct needle size and type for the fabric and design you are stitching.
5. Machine maintenance: Regular cleaning and maintenance are important for the smooth operation of the machine. Clean out any lint or debris from the bobbin area, needle plate, and thread path. Lubricate the machine as recommended in the manual.

www.fixya.com/support/t12525526-keep_getting_check_rethread_upper

3 answers
Apr 23, 2012 - I also kept getting the check and rethread upper thread message, I\'d sew about 15 stitches and it\'d stop. ... up and I spot a little slit in the plastic piece so, when I was threading the machine I guess I was pulling it to .... Instant Repair Help over the Phone ... It may take a couple of trys but it should do the trick. More results from www.fixya.com

https://support.brother.ca/app/answers/detail/a_id/134247/~/error-message-check-and-rethread-upper-thread

It is likely you have the bobbin tension and/or upper tension not set properly. When your foot is down give the bobbin tension and upper tension a tug. The amount should be equal with each other but not so tight to test the thread for strength. In others words you may have to loosen the tension or tensions. Also, be very sure that your upper tension has the thread going between the tension plates.

Try contacting your Bernina dealer. They should know what that error message means.

Perhaps something helpful will be found here:

Bernina Artista 180 check upper thread Google Search

..

Hai, Please check the bobbin tension and winding. And cleaning the machine.

Hi....I also kept getting the check and rethread upper thread message, I\'d sew about 15 stitches and it\'d stop. Here\'s what I did. On the left of the machine, in the back there is a screw....loosen that screw, take cover off, then lift straigt up and out on the cover that has the 3 on it in your threading seqence. Next, I started inspecting and cleaning the thread route from top to bottom. Lo and behold....I get to the place where you come down the front of the machine and turn to go back up and I spot a little slit in the plastic piece so, when I was threading the machine I guess I was pulling it to far to the left causing it to wear a little slit in that piece....so, I finished cutting it off with a utility knife, used an emery board to smooth it down, put the covers back on and it works GREAT!!!! Who would\'ve ever that it\'d be so easy and save me a bunch of money!!! I sure hope this helps someone.

The upper thread sensor on most Brother's is activated by the check spring. Either your check spring has broken or is stuck. You may be able to fix this if you can get to it. A drop of oil may be all you need. I may be able to give more specific advise if you tell me what model it is.

Good luck!

same thing with mine. it stops after 8 stitches every time. now if i use it, i will go for 7 stitches, then let off the presser foot, and start again for 7 stitches. i've tried everything.