Question about Frigidaire 24 in. PLD2850 Built-in Dishwasher

1 Answer

Same old demon

The trick with the ribbon didn't help. I took the latch off and inspected it, trying to figure a way to bypass it. When I re-installed it the machine worked for 2 washes and now is b ack the same way.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,314 Answers

Id replace the latch assembly as one of the switches is not working all the time

Posted on Mar 23, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Bosh SHX7ER55UC door won't latch. Trying to figure out the 2-screwdriver method but can't figure out what part to push/pull.


HOW TO FIX YOUR BOSH DISH WASHER DOOR LOCK ...

? 11:11
https://www.youtube.com/watch?v=_uPK5mJmvZM
Jul 23, 2013 - Uploaded by Andrew Wallace
Dishwasher Door Latch (part #W10275768) - How To Replace ...Dishwasher Door Latch Replacement - Bosch DishwasherRepair (part ...

Nov 29, 2015 | Bosch 800 Plus SHX7ER55UC Fully Integrated...

1 Answer

I have a KitchenAid KUDSFLxxx dishswaher - a couple of weeks ago it stopped working (looked dead) - I took the door apart and tested the switches in the door latch - tested good - started playing around -...


Hi


If you have replaced the control panel then it is the electronic control board that is bad and should be replaced. If you have replaced the electronic control board then check the door latch, it can be due to the latch & control not operating. Hope this helps...please post back with its model no. for further assistance.


Daniel

Dec 08, 2010 | KitchenAid 24 in. KUDI01FLSS Stainless...

1 Answer

Soap dispenser will not close stays open will not latch


Turn off power to the machine. Remove the inner door panel and inspect the dispenser cover latch for any broken components. If everything looks ok, check the action of the release solenoid by hand. If it is sticky or stuck closed, try removing the center pole piece and clean the solenoid interior and pole piece with a small rag or 'Q tips' with WD40. Don't otherwise lubricate the solenoid. Push the cover closed and push the solenoid pole to release the latch, then repeat the process again. If the cover will latch again, you can replace everything and try a load of dishes. Hope this helps

Mar 29, 2010 | Bosch Dishwashers

1 Answer

Need door latch diagram Kitchen Aid dishwasher (Part No. 9744033)


I thought the metal bar had to be locked into place somewhere in the black latch. This was not the case. I just put the white plastic latch in place in the slot in the door and closed the panel and the metal bar went into the correct position against the black latch.

Jan 22, 2010 | KitchenAid KUDS24SE Built-in Dishwasher

3 Answers

Cannot select any wash cycle but quick wash. No other wash cycles will light up when selected. If you select the start button, the quick wash lights and the dishwasher starts (even with door open).


I had this same problem and being an electrical engineer, I decided to see what I could fix before replacing the board. The symptoms were the only cycle I could run was the QUICK WASH - no other cycle buttons responded.
I took the inside panel off and the cover plate off of the circuit board - just a few screws. Nothing on the PCB look scorched or burn and the silicone protection looked to be in tact. But I got it fixed - see below:
Remove power to the dish washer. Follow the ribbon cable from the top panel to the circuit board. Push back the white slider latch and pull the ribbon cable out. Using a knife edge, softly scrape off the connections which face the top side. wipe off with a towel when done and push back into the connector. make sure to pull the white slider latch back down to secure the cable.
that is all it took and we are back to washing dishes! Hope this helps.
JC

Nov 02, 2009 | Jenn-Air 24 in. JDB1080AWS Built-in...

2 Answers

Maytag quiet series 200 dishwasher won't start


I had a similar problem. Turn off the power to the dishwasher. Open the door and remove the screws on the back that holds the door together. Now, locate the black control module and remove the cover. Look down at the bottom left of the control module and you should see a ribbon cable. This is the cable that connects the door keypad to the control module. Unplug the ribbon cable and the plug it back in. On my unit the ribbon cable was not making good contact and only half of the keypad was operational,

Hope This Helps !!

James D.

Jul 28, 2009 | Maytag 24 in. MDB5600A Jetclean II...

1 Answer

Latch wires


wireing schematic is behind the kick plate

Jul 12, 2009 | Maytag 24 in. MDBH950AW Built-in...

1 Answer

Latch cover on dishwasher soap dispenser no longer functions.


hello there. i hope i can help you?. please check the latch spray a little wd40. and give the soap dispenser. a good clean with warm water. please check that you are useing the correct soap? as this can cause alot of problems. check once a week.top tip give the machine a good clean once a month. i hope this has helped you marymena? also please check for any little obstructions.

May 08, 2009 | Frigidaire Dishwashers

10 Answers

Frigidaire dishwasher FDB1050REB0 flashing washing light but doesn't start


Fliped the circut breaker and got the 3 blinking lights and hit start and it ran fine.

Apr 18, 2008 | Frigidaire 24 in. FDB1050REC Stainless...

1 Answer

Soap door latch


clean out the soap latch area with water and try using liquid detergent.
failing that, you need to replace the latch.

for the question from 'guest', the wash arms not spinning relates to either a build up of minerals or a pump that is not pushing enough. clean the unit with a mineral deposit remover, and then run a few loads with just water. clr might do the trick, but check the label for conflicts with the materials in your machine.
good luck
mark

Dec 13, 2007 | Whirlpool GU2400XTP Built-in Dishwasher

Not finding what you are looking for?
Frigidaire 24 in. PLD2850 Built-in Dishwasher Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Dishwashers Experts

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Frigidaire Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...