Question about Projection Televisions

1 Answer

Can you tell the age of a television by the model number The model number is C-13CL4/C-13WL4 or C-20Cl4 I'm not sure which as it shows both numbers at the back of the user guide under the title Specifications Thank you

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 149 Answers

Around 1994 i think

Posted on Mar 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My sony kp-43t90 is blury


Convergence problem and because of age of set may not be worth shop repair-----Tvrepairparts.com sells kits based on model number for this.
11_5_2012_4_04_17_pm.jpg

Nov 04, 2012 | Sony KP-43T90 43" Rear Projection...

1 Answer

Why does my projector start flickering or flashing?


hard to tell without knowing the model number and or age of the set-like my car runs poorly etc.

Apr 24, 2012 | Epson Projection Televisions

1 Answer

Rear projection 48 inch mitsubishi. Actually intermittantly goes blank, then back to picture, every few seconds. Not sure it's worth repairing, although it's been working well for a number of years.


A number of things will cause set to go "blank".

The most common problem is sets like this develop bad solder connections which is normal from age etc.

Provide me with exact model number so I can assist you more. You do have to be careful fixing a set over 10 years of age as some parts are no longer available.

These sets are very well protected, if a vertical problem where loss of picture, the set will blank all three picture tubes to prevent a line or spot being burnt into all three tubes.

The more you tell me the better I can assist you---model number and year set made will be on the back of the set.

REGARDS, SD TECH

Aug 10, 2010 | Projection Televisions

1 Answer

MY HITACHI HDTV I TURNED OF UNPLUGED IT AND NOW IT DOES NOT WANT TO TURN ON


Hi, if you describe the led light indication, a more accurate diagnotic solution can be provided. However, depending on the age and model number, it would most likely be the lamp or color wheel. You need to give model number, type of tv, number of blinks and any other indication like whining sound etc, Check out www.fixurtvs.com for more FAQs and solutions.

Mar 02, 2010 | Hitachi Projection Televisions

2 Answers

Mitsubishi ws-73903 73" red convergence is stuck and won't move.


I have to presume you have got the model number wrong--WS-73903 does not show as a good model number.

Correct model number will be on the back of the set along with month, year the set was made.

If you have a convergence problem with the valid model number I can tell you what parts need to be replaced and in many cases I have Start to finish, step by step instructions for this repair.

The instructions based on model number are free and if available for your model I can post them here for you.

If you are not able to do the repair most shops are going to charge 300 or more for this kind of repair--all the parts usually needed can be purchased on Ebay for under 30 dollars.

If this information has helped you rate this solution as I do this here for free.

SD TECH

Dec 10, 2009 | Mitsubishi WS-73903 65" Rear Projection...

1 Answer

I cannot adjust the blue with the remote. Is there way to adjust.


WS-55805 ?

Look on the back of the set and confirm the correct model number--55805 does not show as a good model number.

If blue will not adjust what ever it uses (either one or two convergence chips need to BOTH be replaced and then the set adjusted.

I HAVE START TO FINISH, STEP BY STEP INSTRUCTIONS FOR THIS REPAIR for most of these sets.

Double check the model number and let me know and I will tell you what parts it uses and also then be able depending on the model number to give you the instructions etc.

If this has helped you rate this solution as I do this here for free.

SD TECH

Dec 09, 2009 | Mitsubishi WS-55805 55" Rear Projection...

1 Answer

Yes i read the questions and i think i have the same problem with my big screen tv, my serial # is pl 565159 can u tell me how old it is


well you can tell on the back where you found that model no and serial number there is a production date stamped on that tag as well
and its a HD its not more then 5 yrs that when they switched to that new cabinet style
hope this helps you determine your age of your unit

Nov 18, 2009 | Philips Magnavox 51MP392H Rear Projection...

1 Answer

My Mitsubishi tv will not turn on.


If you have the owner's manual, you will find that the blinking light is an indicator that the lamp or fan is the problem. I'm not sure of your model number. Can you confirm that model please? If you no longer have the manual, once you confirm the model number, I can look up the code for you. Given its age, I would suspect that the lamp needs to be replaced.

Please post the model number and I will confirm.

Thanks,
Dan

Feb 20, 2009 | Mitsubishi WD-52725 52". Rear Projection...

Not finding what you are looking for?
Projection Televisions Logo

Related Topics:

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Projection Televisions Experts

Jaime Hernandez

Level 3 Expert

2267 Answers

matt martin
matt martin

Level 3 Expert

1191 Answers

yadayada
yadayada

Level 3 Expert

61168 Answers

Are you a Projection Television Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...