Question about Other Network Devices

1 Answer

Pin Code I have a Picturetel 740 videoconference unit but cant change it from ISDN to Lan as we have no manuals and Polycom who brought out Picturetel can't help us

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 47 Answers

Check this out:
http://www.polycom.com/common/documents/support/user/products/video/picturetel_760_compact_system.pdf

This should work with your product.

Let me know what happens

Posted on Apr 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Error code sc 390 code richo aficio 2045


That error is related to a bed reading in a sensor of the Development Unit, called "TD sensor".
You can try to take out the development unit and see if there is dust of toner or even if the plug is broken.
The development unit is placed under the PCU.
Open the front door and you will see it.
If you can not see anything abnormal like dust or broken plug i advise you to call your provider to change the TD sensor or the development unit.

Jun 02, 2011 | Other Network Devices

1 Answer

Lantronix UDS1100 what are the pin connection to emulate com1 on a PC


Please see the link here below for the complete manual.
http://www.lantronix.com/pdf/UDS1100_UG.pdf

If you go to page 70 you will see the complete pin layout for RS232, if you need to connect it to a PC with a 9 pin RS232 port you can see the equivalent on page 72.

Please let me know if you need more details.

Mar 15, 2011 | Lantronix UDS1100 (UD110000201)

1 Answer

I purchased Compaq Presario CQ50-106AU Notebook PC and installed Win Vista and i am not able to find the drivers for lan and lan is not detected


go to BIOS Set up...try to LOad DEFAULT all the settings...

start up again , if one can found a new hardware.. try to install the LAN CARD drivers....

follow the set up...

Oct 19, 2009 | Other Network Devices

1 Answer

Enable LAT protocol on Shiva Atom?


Since the only thing that changed was the Shiva Atom, I'm guessing that the license error is coming from the terminal server itself rather than the VAX, corrrect? My only suggestion would be to replace the ethernet chip on the new server with the one from the old server. Perhaps the license is tied to that address. It should be a small 8 pin IC in a socket. At the time of these units being built, the Ethernet ID chips were usually installed in sockets.

Hope this helps,
Dan

Apr 30, 2009 | Intel ShivaPort Atom (SATOM16TX) Terminal...

1 Answer

Centrios internet radio gives dhcp timeout


This is likely because out of the box, the firmware for this unit doesn't support WPA2 and even certain variants of WPA. I recommend: configure router for WEP or even open (i.e. unencrypted) connection, connect unit, go to setup/update firmware and let it update from network, power cycle, reconfigure your router for WPA or WPA2 security, attempt to reconnect unit to wifi. The updated firmware supports more formats and may allow your new router's config to work. You can also try doing the firmware update over the wired LAN port. Hope this helps.

Sep 27, 2008 | Other Network Devices

1 Answer

Networking problem


configure your local nw with static ip, might solve ur prob.

Sep 17, 2008 | Other Network Devices

1 Answer

Puk code formotorola c168i


Contact your carrier/wireless provider for the code.

Jul 30, 2008 | Other Network Devices

2 Answers

Manually resetting my Alvarion breeze access indoor units


sorry mate trying to make heads or tails of what you have written, to get the IP address of the device you need to do this. connect to the device, then click start button, then click run, type CMD and press enter a black screen appears ie dos prompt. type IPCONFIG /ALL then press enter you will get the IP Adress of the device. dont matter if you connect wirelessly or through cable you will get the ipadress.. Hope this is what you mean All the best John

Mar 08, 2007 | Alvarion (835108) Wireless Bridge

1 Answer

Reprogramming


Open Internet explorer and type the ip address of the router in the address bar and hit enter. (it should be 192.168.1.1) The setup page for the router should open. Click "Advanced" then click "ISDN Configuration" then click "ISDN Parameters" You can enter the new SPID's the phone company gives you there. Good Luck, El Duderino

Nov 15, 2006 | Ramp Networks WebRamp 410i (516S)...

1 Answer

Help with my wet11


Can you connect to the built-in Web server or configuration screen?

Aug 07, 2006 | Linksys Instant Wireless Wireless Ethernet...

Not finding what you are looking for?
Other Network Devices Logo

Related Topics:

103 people viewed this question

Ask a Question

Usually answered in minutes!

Top Other Network Devices Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

Coss

Level 3 Expert

1043 Answers

Tony

Level 3 Expert

2598 Answers

Are you an Other Network Device Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...