Question about Asko W6441 Front Load Washer

1 Answer

Asko Frontload wont stop running water

This past friday there was a neighborhood water emergency and the water was shut down for several hours. When I started the washing maching i heard pressure release sound comming from the water source and since then I've had the following problem

Here is the problem : Water won't stop filling the machine and spin cycle does not automatically start.

1. I start the washer
2. It fills normally
3. The spin cycle will not automatically start.
4. The Machine will continue to pour in water and drain continuously -- it did this all night long on Friday.
3. Even when the door is open, water starts pouring into the machine.

Is there something I can do , without calling a repair person.

Thank you very much for your help.


Posted by on

  • Anonymous Mar 17, 2014

    machine starts , goes through wash cycle will not empty or go to spin, therefore will not turn off then door will not open unless released by using manual pull at the pump/ needle catchment door

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 351 Answers

You need a new inlet valve take off the top panel then you see the inlet valve follow the inlet hose

Posted on Mar 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Asko washing machine wont go into spin cycle it just keeps on washing after 3 hours I had to turn it off now what


call a technician in
the problem is most likely in the program board not progressing the wash cycle

Jul 12, 2016 | Asko W6021 Front Load Washer

1 Answer

Whirlpool frontload WAsher. After I run a load, the clothes come out fine. Several hours later there will be an inch of water in the tub. 10 hours more there are 5 inches of water. I have checked the...


It sounds like the water inlet solenoid valve at the rear of the washer where the hose hooks up is leaking, more than likely the cold water valve.

Jan 31, 2012 | Whirlpool Washing Machines

1 Answer

Can't open door of ASKO W6883


If nothing else works, the washer door can be opened as follows:

This must only be done in an emergency

if the machine's glass door does not open automatically when the program has finished.

First check that there is no water left in the machine. If there is water left in the machine and it is not possible to run the Drain program, empty the machine by using the drain hose.

Make sure that the main power switch is off and that the plug has been re- moved from the wall socket.

You will find the emergency opener for the glass door in the double sealed bag.

Open the glass door by putting the opener in the slot to the right of the lock on the door. Push the opener up or down and the door will open.

Feb 28, 2011 | Asko W6021 Front Load Washer

1 Answer

How make the door open automatically when finish the laundry


Hello,

Welcome to FixYa,

These model of Asko ( based on the number listed ) do not have such an option. On these models the Program Control knob must be at the end of a program (at the 12:00 or zero position) to open the glass door.

If you need to stop or interrupt a program after you start the machine, turn the Program Control knob

to 10 (Drain). Any water in the machine will be pumped out and you can then press the Door Open

button ( ) to open the door. To restart the washer, close the door and turn the controls to the desired
settings.

On the electronic control models, if you need to open the glass door during a wash or rinse cycle, press and hold the Door Open button for three seconds. The machine will stop and automatically drain enough water so the door can be opened safely. The program will resume when you close the door. The inlet valve will come on to

ensure the proper water level.


In case of mechanical failure, you can use the Emergency Door Opener located by the drain pump. To use the Emergency Door Opener, remove the screw holding the cord handle (loop) and pull the cord down.


Hope this answers your question even if it isn't necessarily the answer you wanted. Thank you for choosing FixYa and good luck.


Regards,


Macmarkus :)

Jan 10, 2011 | Asko W6021 Front Load Washer

1 Answer

My Asko Front load washer model W6021 Prewash


hi you need to replace the inlet valve,take off the top panel and you will see the valve behind the soap drawer with the black hoses.you can get a book from asko.com.au

Jun 15, 2010 | Asko W6021 Front Load Washer

1 Answer

Asko frontload quit spinning


check water pump,clean out call asko tech line may be motor or control board both expense

Feb 03, 2010 | Asko Washing Machines

1 Answer

I have an asko 11505 clothes washer. For some reason, it is not going through all of the spinning cycle, it spins for a short time, then stops abrutely. I cleaned the coin stop, cleaned out all water...


My Asko 11505 washer fills only a little water then shuts off. If I drain the washer with the drain hose from under the machine, then the machine will start up and fill enough water to fill the hose again, then shut off.

Oct 19, 2009 | Asko Washing Machines

2 Answers

Asko WCAM1812 Front Load All-in-One Washer / Dryer It does not start the lights are blinking on spin. the door remains unlocked


hold down the "cycle signal" button for 3-5 sec. unplug and plug back in. should clear and reset computer

Aug 08, 2009 | Asko WCAM1812 Front Load Washer / Dryer

1 Answer

Machine wont stop filling with water, it just overflows. Machine is an Asko w6551 front loader


Same thing happened to my ASKO W600.  Sounds like the water inlet valve is blocked or broken so therefore can't stop the flow of water coming into machine.  Check it out and replace if necessary.

Oct 30, 2008 | Asko Washing Machines

3 Answers

Asko W620 washing machine not spinning


Sounds like the motor brushes need to be cleaned or replaced. Take the back off the washer, remove the motor and gently scrape the excess carbon or debris off the brushes with a pocket knife. I did this and it ran well for about 50 loads before building back up. I am ordering new brushes now because when I checked the brushes last week they were obviously worn more than 4 weeks ago.

Dec 11, 2007 | Asko W620

Not finding what you are looking for?
Asko W6441 Front Load Washer Logo

313 people viewed this question

Ask a Question

Usually answered in minutes!

Top Asko Washing Machines Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1456 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3051 Answers

Are you an Asko Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...