Question about Siemens SX66

1 Answer

Siemen sx66 my back light out

I tried set up and setting. I did a reboot. nothing seems to work.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

I don't have an SX66. I have an SX56, but have you tried holding down the power button for several seconds while it is still on? With the SX56 that "toggles" the backlight display. You could also try settings for the backlight in the menus. Otherwise, the backlight may be dead. Best bet is to purchase a new or used one on ebay or other location.

Posted on Sep 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Siemens SX66 align screen does not get aligned.


Go to system/screen/align. Realign

Oct 27, 2009 | Siemens SX66

1 Answer

Freezed SX66 at the initiation Windows page


Hi there,

This could be an internal problem on the device, cause of instant shock cause of dropping it. You better try to remove the battery for a while to reset and restore the system.

If the above recommendation did not solve the issue, try to remove the memory card, if still not working try to update the firmware of your unit.

Let me know here again for the update.

micro

Jul 19, 2009 | Siemens SX66

1 Answer

Sx66 got wet. now acting spastic!!!! Did I kill it?


Yup....and I sell em. Love em. Bobzmailroom@yahoo.com

Jun 24, 2009 | Siemens SX66

1 Answer

My messages keeps on refreshing


You have a problem I would love to have. I can't get any. At any rate. Go to settings and change refresh rate to timed.

Jun 05, 2009 | Siemens SX66

3 Answers

Phone keeps rebooting


is the button near the reset hole? possibly the button is somehow pressing the reset switch, possibly stuck somehow. Other than that try a hard reset, instructions below.
Soft Reset
Put your stylus in the hole in the lower left corner where it says “Reset” Soft Reset will reboot your device just like when you reboot your PC. No data will be lost, under normal circumstances that is.

Hard Reset
Hold down the Power button (Top Right corner) and at the same time put your Stylus pen in the hole where it says “Reset” (Lower Left corner).
Hard Reset will delete all data you have put on the device, Programs, Settings, Mail, SMS, MMS, etc., so be careful and make a backup before doing this.
After a hard reset, you will have a complete clean new install of Windows Mobile on your device.

Things that are not deleted
  • Data on \Storage Card
  • Data in \Storage folder

Oct 15, 2008 | Siemens SX66

1 Answer

Screen says USB or Serial on top and v2. 07 at the bottom


Open the Back Cover.. remove the Battery, Simcard, Memory Card and then leave it open for 1 minute.
Put the battery back, start your device then if you get the same message you need to update the firmware...
In the worst scenarios, your Siemens SX66 has a corrupt ROM and need to be fixed as in "Hardware"... which can be done by a Siemes expert.

Good Luck

May 23, 2008 | Siemens SX66

1 Answer

Siemens sx66 wont work


Download mitty 1.42 file from this website.
www.tompda.com/bbs/display.asp?forumID=2052114&luntan=27

Mar 24, 2008 | Siemens SX66

2 Answers

WiFi


Go to Configure Wireless Networks
select the wireless after say connected doble click that connection when open the another screen with network name verify you network name is correct, in Connects To: verify select The internet. In the next tab select you Authentication and Data encrypted as you have in your router. and type your network key. select ok. Verify en the next tab if your select USe 1EE... and select EAP typel, select ok. Verify do you have W up in your PDA.
Lucky

Mar 07, 2008 | Siemens SX66

1 Answer

Sx66 to tmobile


As I understand it, the SIM card is what tells your wireless unit which service provider to use. If you have an old phone, it should be an easy matter to take the t-mobile SIM card out of it and install it in the SX-66. One note on the SX-66: the SIM card on mine had a tendency to lose contact (and my contacts would disappear) from jarring until I put a piece of scotch tape across the bottom of it. No problems after that.

Nov 29, 2007 | Siemens SX66

1 Answer

VERY WEEK NETWORK IMEAN SIGNAL VERY LOW


Network signal strength is not based on your phone. It is based on the network. Poor sigal is their problem, Call them. If this rates as helpful, please post as such.TY

Sep 11, 2007 | Siemens SX66

Not finding what you are looking for?
Siemens SX66 Logo

Related Topics:

321 people viewed this question

Ask a Question

Usually answered in minutes!

Top Siemens PDAs Experts

k24674

Level 3 Expert

7987 Answers

kakima

Level 3 Expert

96417 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Siemens PDA Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...