Question about Washing Machines

1 Answer

Won't rinse, fabric softner still in basin and won't drain. clicking noises when chaning cycles to rinse and drain

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 178 Answers

Sounds as if the pump may be clogged or going out. You'll have to scoop the water out of the tub and tip the washer on it's face to inspect the pump. I persoanlly have had a sock be sucked into it and cause the same problem. I wish you luck, if you need more assistance, please feel free to ask me.

Posted on Mar 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When putting softner in after loading clothes, the fabric softner runs out onto clothes before washing cycle begins


The part that puts softner in at the right time might be stuck open or broke. Have it looked at or see if you can find the problem.

Jan 23, 2014 | Kenmore Washing Machines

2 Answers

Kenmore Oasis HE 27082 Front Load Washer


ohm the release solenoid. could be shorted or open. check for voltage to the circuit

Sep 22, 2008 | Kenmore Oasis HE 27082 Top Load Washer

1 Answer

Htwp1200doww where does fabric softner go


You have to do it manually. Ugh. See below from manual:

Liquid Fabric Softener (Manually add during rinse cycle)
1. Turn OPTIONS knob to FABRIC SOFTENER
2. Measure liquid fabric softener carefully, following instructions on the bottle, and add during the rinse cycle.

OPTIONS (on some models)
Set this option when planning to manually add fabric softener during the rinse cycle or when you use extra detergent or bleach to clean hazily soiled items. It provides an enhanced rinse.

Oct 04, 2012 | Hotpoint Washing Machines

2 Answers

How to add fabric softner to the amana washer with locking lid


Check and see if there is a cup in the top of the agitator. Some machines have you put it there, turning back and forth during wash doesn't bother it, but the spin to empty the wash water causes the softener to go out through slots in the top of the cup and be held in the agitator. when it stops the softener drains into the tub, ready for the rinse cycle.

May 30, 2012 | Amana Washing Machines

1 Answer

My washer will not complete a full cycle.. when on rinse does not finish beeps as though it done but is still on rinse..also fabric softner does not drain into machine. machine will spin if I manually set...


my washer does not finish a full cycle ;but is still on rinse and its a bosch and i was wondering
were is the fuses kept in the machine,

sandra read

sandrarread@yahoo .co uk

Jan 22, 2011 | Bosch Nexxt 100 Series WFMC1001UC Front...

1 Answer

F02/Sud error message fabric softner will not dispense


The pressure switch is sensing that there is still water in the unit,it sits at the top of machine under the top cover,it is round and usually red in color remove the hose/tube from it and blow through it to make sure it is clear,you can also remove the switch itself and lightly blow into it you will hear a couple of clicks put it back together and give it a shot..

Sep 03, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Takes almost 2 hours to complete a wash cycle


Have you ever cleaned it out? Its likely due to a plugged drain, not allowing the system to drain fast enough for the normal cycle. Check out my solution on
http://www.fixya.com/support/t114322-kenmore_elite_h3t_washer

-Todd

Mar 30, 2009 | Kenmore 3.8 cu. ft. HE3 Front Load Washer

1 Answer

The fabric softner drains out as soon as I pour it in


the fabric softner drains or flushs down in the rinse cycles,,,now if you fill past the line or open in dispencer it will sphion down by it self,,in short your overfilling dispencers,,onthejob

Jan 07, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

Fabric softner


Remove the dispenser tray. Inspect the area just above the fabric softener portion of the dispenser. There should be a series of holes where water feeds into the tray during the rinse cycle. Sometimes these holes become clogged with fabric softener residue. If the holes are clogged, water will never dispense the fabric softener out and it will stay in the tray. If you take some cotton swabs and meticulously clean all the holes out, I bet your problem will go away. Let me know if this was helpful to you.

Oct 05, 2007 | Frigidaire GLTF2940ES Front Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8147 Answers

Richard Roth
Richard Roth

Level 3 Expert

9472 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...