Question about Frigidaire PLDB998A Built-in Dishwasher

2 Answers

Just had a power outage, dishwasher is dead

Just had a power outage while the dishwasher was in cycle. Normally I would see a blinking code, not this time it just won't respond to anything. I checked a the breakers and they are on but the dishwasher will not respond. Help!!! I have a load that I will need to hand wash. The dishwasher is only 5 years old.

Posted by on

  • Anonymous Jan 02, 2009

    Just had a power outage while the dishwasher was in cycle. Normally I would see a blinking code, not this time it just won't respond to anything. I checked a the breakers and they are on but the dishwasher will not respond. Help!!! I have a load that I will need to hand wash. The dishwasher is only 5 years old.

  • Anonymous Apr 30, 2009

    Washer stops mid cycle and flashes "PF"

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the exact same dish washer and it also just quit after a recent power outage. Normally would blink PF but I get nothing -- breaker is good and tested to be sure power is getting to the unit. Any help would be appreciated.

Posted on May 29, 2011

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Frigidaire Master
  • 2,651 Answers

Althought e breakers apear to be on physcally turning them off and then back on especcially after power flashes(the breaker might of partially tripped, and needs to be reset(possible)

Posted on Mar 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kid 60 s10 please give fault codes


Hi Roger, Hope this helps......CHEERS..

KENMORE DISHWASHER ERROR CODES

Kenmore Dishwasher Error Code = Start Resume light blinking slow
When the dishwasher door opens or electrical power is removed during the cycle then the dishwasher will not start again. The door is detected as being closed and the Start Resume button is being pressed
Kenmore Dishwasher Error Code = Clean light is blinking 7 times
Heater circuit fail. Control panel did not detect the water getting hot. Did not detect heating element was energized to heat the water during the wash cycle
Kenmore Dishwasher Error Code = Sanitize LED blinking at end of cycle
Control panel could not detect if sanitation has been achieved
Kenmore Dishwasher Error Code = Console light blinking rapidly
There is a stuck button on the control panel
Kenmore Dishwasher Error Code = Clean light is constantly illuminated
Dishwasher cannot start a wash cycle until it sees that the door has been opened after the previous washing cycle
Kenmore Dishwasher Error Code = Control lock LED is ON but not responding to pressing of the keys
Turned on by accident or there is a control detected key pad problem

Mar 31, 2016 | Kenmore Dishwashers

1 Answer

Why is heated dry blinking?


FIXED Kenmore dishwasher lights flashing: "Hi Temp" & "Heat Dry ...

www.applianceblog.com/.../40588-Kenmore-dishwasher-lights-flashing-...

Aug 26, 2013 - 10 posts - ‎3 authors
Thread: Kenmore dishwasher lights flashing: "Hi Temp" & "Heat Dry" ... A few months ago, we had a brief power outage and the next morning, noticed the "Hi Temp" and "Heat Dry" lights were flashing. ... Well since then, the dishwasher intermittently stops mid-cycle and these same lights ... Thread: GE Eterna QuietPower 2 Normal and Heated Dry ...
6 posts
Feb 24, 2012
Kenmore Elist 665 dishwasher Smart Wash red light ...
6 posts
Dec 23, 2011
Heated dry blinking +17 times - ApplianceBlog
10 posts
Nov 14, 2010
Heated Dry light blinking
3 posts
Nov 7, 2010
More results from www.applianceblog.com

Why won't my dishwasher start and why does the "Heated Dry"

www.shopyourway.com > Manage My Life > Questions
Nov 16, 2009 - When I hold down the Heated Dry button to turn the control lock on it ...my dishwasher start and why does the "Heated Dry" light keep blinking ...

Dec 01, 2015 | Dishwashers

1 Answer

No power appears to be coming in....no connection when door is closed; no lights come on on any of the cycle indicators...deader than a doornail@l


Hello. I need the make/model number to help you most accurately. From the symptom you describe, there might be a main fuse located on or near the main control board which has opened, killing power to the unit. Clues: totally dead--no lights--an open door will not affect indicator lights, the unit won't do anything though--safety(nothing will happen until the door is closed) Have you had a power outage recently? Usually 3-4 weeks after an outage, the damaged chips on the boards start to fail. This can be evidenced by blown control panels, blown main boards, etc. Make sure 120 volts *is* getting to the dishwasher--check the power connections below(be careful). If the breaker has tripped, reset it and see if the unit runs. Troubleshooting starts from the outside and proceeds inward, eliminating the obvious and moving to ever more complex problems until the culprit is found. Definitely supply me with that model number so I can see what I'm dealing with and guide you correctly. Thanks!

Oct 17, 2015 | Dishwashers

1 Answer

Hi, has any one got any idea how I reset the program cycle on my Bosch SGS6312GB/07 dishwasher, any advice would be appreciated. Regards


Hello, usually turning off the breaker for at least 1 minute or more will reset the board. If you are getting a set of lights blinking, that is an indication of a problem--normally, dishwashers will blink certain lights in a pattern(digital error code) and depending on which lights and how many blinks, you have to decipher the type of code from the service manual.

Aug 19, 2015 | Bosch Dishwashers

1 Answer

Dead after power outage


The breaker may have failed electrically while continuing to function mechanically. It may be necessary to replace the breaker, something GE should have been able to tell you without referring vaguely to "an act of nature" which it wasn't.

Feb 26, 2014 | GE Dishwashers

1 Answer

We recently had a power outage, the next time I went to run the dish washer it would only run the lower rack 65 min. cycle. I press cancel nothing happens unless I open the door. I have tried selecting...


Hello Stacey, thank you for your post!

I understand the unit recently experienced a power outage. First, let's try reprogramming the dishwasher. This can be done by either unplugging it or flipping the household circuit breaker to the off position. It is necessary to wait roughly ten minutes and then turn the appliance on. If resetting the power does not correct the issue, your unit could be experiencing a communication error with the control board, or a potential wiring failure. I recommend reaching out to an appliance expert who is best equipped to pinpoint the exact problem, which can often save you funds and a headache.

Sep 10, 2013 | Frigidaire Professional Series 24 in....

2 Answers

I am locked out of cycle with clean light blinking green and cannot find my manual, dishwasher is about 1 year old. Is there a sequence to break this cycle? I turned off power for 60 seconds to no avail.


Hi
I have not seen this model in Australia, but normally if you hold down "Start/Stop" button for 3 to 5 seconds, that should clear the cycle.
Otherwise if you have a Clear button press that for 3-5 seconds.

Ash

Sep 06, 2011 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Pots/pans and normal wash cycle lights blinking fast and soak/scoure continuously lit and start light blinking slow all at the same time. Tried cutting power to reset, it didn't work.


Hello,

Normally removing the power will clear this error code, if not the touch pad is bad. This is a simple repair, you can watch a video that explains how to repair this yourself at the link below.

http://www.appliancerepairlesson.com/

Mar 08, 2011 | Dishwashers

1 Answer

After a power outage my dishwasher has a "Er" code. I downloaded the manual and it says nothing about that specific code. Please help! "Er" code GE Profile Dishwasher GSD4930X66WW


the er means error. you may have a damaged control from the power outage. try to turn the power off to the unit for 30 min then put it back on. see if it resets it.

Jan 10, 2011 | GE Dishwashers

Not finding what you are looking for?
Frigidaire PLDB998A Built-in Dishwasher Logo

1,550 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Dishwashers Experts

Electrolux
Electrolux

Level 3 Expert

4342 Answers

Carmen Mikulic

Level 2 Expert

409 Answers

Mike Cairns
Mike Cairns

Level 3 Expert

3053 Answers

Are you a Frigidaire Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...