Question about EnGenius EOC-3220 (EOC3220)

1 Answer

192.168.1.1 unreachable I tried to reset to factory default by a nullmodem cable with the same result. The network is configured right. If I try to connect via wireless I see the SSID: 802.11g but it's impossible ti surf anyway. I tryed RTLAPConf.exe tool that discover IP looking the MAC address but can't find any device. I think that the web server inside the system is out. When I try to connect via hyper terminal ( null modem cable) I can reach the linux sh ( shell) were it's possible to send some commands ( like flash reset, ifconfig... ... ) Maybe It's possible to re-flash the firmware by null modem cable on hyper terminal... I don't know. Please help me. Thank YOu in advance and sorry for my bad english.

Posted by on

  • Jose Luis Ogawa
    Jose Luis Ogawa Mar 22, 2008

    Hi here,
    I have the same problem, I can not access to 192.168.1.1/2, it happens after I try to upload a new firmware, suddenly did not response. after this I proceed to reset to factory setings, but steel can not access at all.
    On the LAN connection icons, appears not answering the EOC"s to my commands(mean to access to programming), I have two units with the same problems and it happen the same way both. PLEASE SOMEBODY TELL ME, WHAT TO DO, It may need to reset the IP address manualy?? tell me how please!, Thanks Jose Luis Ogawa, Baja Mexico.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You can use the "ifconfig -a" to see the ip addresses of all network adapters. but i'm wondering what happened to the user interface that showed a list of options to choose from.

Posted on Mar 16, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to reset password for motorola surfboard cable modem sb6141


There is no password on the SB6141.
There are no user configurable options. Any configuration is changed through communication with the CMTS.

When you access the modem (192.168.100.1) all you can do is monitor the signal quality and certain log entries.

NOTE: the "configuration" page allows you to reset the factory defaults and to restart the modem. IF you reset factory defaults this note applies:


Resetting the cable modem to its factory default configuration will remove all stored parameters learned by the cable modem during prior initializations. The process to get back online from a factory default condition could take from 5 to 30 minutes. Please reference the cable modem User Guide for details on the power up sequence.

Aug 24, 2014 | Motorola Computers & Internet

2 Answers

My belkin f9k1002v1 router won't work.


A lot of things can keep it from working. Make sure there's lights and you have power, substitute ethernet cables, do a factory reset. Here's how I did the factory reset on my F9K1003V1.

Nov 02, 2012 | Computers & Internet

1 Answer

The router was reset. So, our AP does not work with it anymore. I reset the AP to restore it to its factory default settings and tried to follow the steps I made before in configuring the AP. but i can't...


Before you configure this device, note that when the AP is configured through an Ethernet connection, (via RJ45 Network Cable) make sure the manager PC must be set on same the IP network. For example, when the default network address of the default IP address of the AP is 192.168.1.1, then the manager PC should be set at 192.168.1.x (where x is a number between 2 and 254), and the default subnet mask is 255.255.255.0.
Open Internet Explorer 5.0 or above Web browser.
Enter IP address http://192.168.1.1 (the factory-default IP address setting) to the address location. Please refer here to the Latest User Manual for Encore ENRWI-G Page 9 onwards describes the login details.

Hope this Helps!
CreativeTECH

Jan 01, 2011 | Encore WIRELESS LAN EXTENDER

1 Answer

The router was reset. So, our AP does not work with it anymore. I reset the AP to restore it to its factory default settings and tried to follow the steps I made before in configuring the AP. but i can't...


Before you configure this device, note that when the AP is configured through an Ethernet connection, (via RJ45 Network Cable) make sure the manager PC must be set on same the IP network. For example, when the default network address of the default IP address of the AP is 192.168.1.1, then the manager PC should be set at 192.168.1.x (where x is a number between 2 and 254), and the default subnet mask is 255.255.255.0.
Open Internet Explorer 5.0 or above Web browser.
Enter IP address http://192.168.1.1 (the factory-default IP address setting) to the address location. Please refer here to the Latest User Manual for Encore ENRWI-G Page 9 onwards describes the login details.

Hope this Helps!
CreativeTECH

Jan 01, 2011 | Computers & Internet

1 Answer

How can I clear / reset a Cisco IP Phone 7910


How to set a Cisco IP phone to factory default Reset configuration of Cisco IP Phone (7910, 1911, 7940, 7941, 7960, 7961)

To set the Cisco IP phone to factory default completes the following steps: should be completed:

For 7940, 7941, 7960, 7961 phones:

1. Power up the phone (unplug power cable and plug in again and hold the # key.
2. Release # when lights start flashing.
3. Press 123456789*0#.
4. Press 1 to keep network configuration or 2 to lose the network configuration.

For 7906G and 7911G phones:
1. Power up the phone (unplug power cable and plug in again and hold the # key.
2. Release # when MWI starts flashing.
3. Press 3491672850*#.

Oct 28, 2010 | Cisco 7910 IP Phone

1 Answer

Wireless connection lost - unable to access properties (error)


You can solve the problem by reseting the router

Plese make sure you hard wire the Router to the computer (Using the Ethernet Cable)

Use the following steps to reset the router using this method:
  1. Open your Web browser and enter the IP address of your router. By default, the address is “192.168.1.1′.
  2. Enter your user ID And password when prompted. Hopefully this has been changed, but if it hasn’t, the default is no ID and “admin” as the password.
  3. At the top of the Web page, click “Administration” and then “Factory Defaults”.
  4. Beside “Restore Factory Defaults”, click “Yes”.
  5. Now click the “Save Settings” button at the bottom of the Web page.
Your WRT54G wireless router should now be reset to the factory defaults.
----
If you were trying to uncheck the box for Use Windows to configure my wireless network settings you can change it by disabling the "wireless zero configuration"....i guess you are using Windows XP...if it is Windows Vista...you got to disable "WLAN Auto Config"(Not recommended, as vista works best with defualt windows utility i.e. WLAN AutoConfig)

Go to start...click RUN (Or Simply Press Windows Key and Letter 'R' together on the Keyboard)
Type in services.msc
Scroll through the bottom of the page
Highlight Wireless Zero Configuration and do a right click to select Properties
Go to Properties and click on Startup Type and change it to disable
Click on Apply and click OK

----
Just a small advice do check for any kind to Electro-Magnetic interference caused by any devices like - Microwave,Cordless phone,Mobile,Fridge, or electronic device as they may interfere and may not let the Router and Computer to connect

Jun 10, 2010 | Linksys Wireless-G WRT54G Router

1 Answer

I have a wr850g router which has worked well for 3 years. I tried to configure the network to have a security access code. Partway thru the process I lost access to the router and cannot now reenter...


If you lost your password, you need to reset your router to the factory default and configure it from scratch.

Pull out your router manual or download the PDF file from this (http://broadband.motorola.com/consumers/products/WR850g/downloads/WR850G_userguide.pdf). Follow the instructions from it to:
  1. find out your logon details from your service provider
  2. reset your router to factory default
  3. use a network cable to connect the router to a computer to re-configure the router

Dec 17, 2009 | Arris WR850G Router (DHWR850G)

1 Answer

I cannot scan or fax after multiple tries. Can you assist


Hi

Thanks for using FixYa. Try to reset the printer by power cycling it for 4-5 min.s. Also tell me if you are able to print and not fax/scan. Make sure that all the cables are plugged in well. Also tell me if you are getting any error messages on the printer as well as on the computer.

Try and reset it & check if it works. To reset the printer go in the configuration menu where you can reset the printer back to factory defaults.
  • Press and hold the Start and Stop buttons and turn on the printer.
  • Hold the buttons down until “Performing Self Test” is displayed on the LCD.
  • Release the buttons and “Configuration Menu” is displayed.
  • Scroll to the RESTORE FACTORY DEFAULTS item on the menu and press select.
  • Now scroll to RESTORE BASE and press select this should reset your network card password.
  • There is also a RESTORE NETWORK, this will erase the network configuration but will not reset the password.


Please do accept the solution if the issue is resolved or else revert for further assistance.



Thanks

Rylee

Sep 24, 2009 | Lexmark X5470 All-In-One InkJet Printer

2 Answers

My brother printer MFC-640CW has stopped taking comand to print documents from my computer, i can copy and scan, but not print . ink pads are full.


Make sure the status and configuration of the print server. Check following:

1 Make sure that the machine is powered on, is on-line and ready to print.

2 Print the Network Configuration List of the machine and check if the settings such as IP address settings
are correct for your network. The problem may be the result of mismatched or duplicate IP address.
Verify that the IP address is correctly loaded into the print server. And make sure that no other nodes on
the network have this IP address.

3 Verify that the print server is on your network as follows:
For Windows®
(1) Try pinging the print server from the host operating system command prompt with the command:
ping ipaddress
Where ipaddress is the print server IP address (note that in some instances it can take up to two
minutes for the print server to load its IP address after setting the IP address).
(2) If a successful response is received, then proceed to Windows® 98/98SE/Me Peer-to-Peer print
(LPR) troubleshooting
. Otherwise, proceed to Step 4.

4 Reset the print server back to the default factory settings and try from the initial setup again. For
information how to reset to the default factory settings, see Restoring the network settings to factory in the manual.

Jul 01, 2008 | Brother Office Equipment & Supplies

6 Answers

How to probe the configuration or reset the 2700AP?


Restore it to default, with these things, if it wont work on automatic, then something is worng.

Feb 27, 2008 | D-Link AirPremier DWL-2700AP 802.11g/b...

Not finding what you are looking for?
EnGenius EOC-3220 (EOC3220) Logo

756 people viewed this question

Ask a Question

Usually answered in minutes!

Top EnGenius Computers & Internet Experts

john smith

Level 2 Expert

381 Answers

WTF Chuck.....
WTF Chuck.....

Level 3 Expert

386 Answers

Jacqueline

Level 2 Expert

76 Answers

Are you an EnGenius Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...