Question about Krups V65 Iron

1 Answer

Rust can u please advise if the steam holes can be unclogged it looks like my wife was leaving water inside me machine and it is now bringing out rust on clothes or it is clogged does this mean the machine is gone?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,889 Answers

No. The machine is not gone but you may have to replace the steam compartment of the machine.. You can also try cleaning the rust.. You will need to get a pair of gloves open the steam compartment and clean the rusted area with dilute oxalic acid.. It will work more often than not..
Good Luck!

Sai.

Posted on Mar 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My iron is steaming out rust coloured water how can I clean it please


Having been asked this many times, I wrote it as a Tip to save me writing each time.

Tip & How-To about Irons
Cleaning a Laundry Iron

Get some CLR descaler and mix it to the directions. Turn the iron on and set it to steam. Turn the iron off and put the CLR into it. When it has cooled a little, sit it faceplate down in an oven proof dish. Leave it over night. The CLR will drip through and sit in the dish cleaning the inside, and the topside of the soleplate. The next day, fill with water and shake upside down to empty any remaining CLR and scale through the fill hole. Keep filling and shaking to empty until the water comes clean.

If you don't want to use CLR, you can use white vinegar undiluted.

Posted by Andrew... on Mar 18, 2016

Apr 24, 2016 | Oreck Cordless Steam Iron

1 Answer

No steam coming throwc


Normally when water is put inside steam irons, it get stored in tank then if thermostat knob is set for steam then water moves to bottom heated portion of iron. Water converts to steam as base plate is hot, heated steam comes out through perforated holes. If holes are blocked due to scale formation steam flow is blocked. The descaling has to be done as per instructions given on descaling wax manufacturer. sometimes if water does not enter through a rubber washer that is water tank to heated bottom portion then also steam will not get generated hence no steam. Please check above points and identify the problem.

Jan 08, 2015 | Irons

1 Answer

Rust coming out of steam holes


dump what water is still in iron. refill with white vineger turn turn on after a day soaking with iron hot use on old towel. dump remainer out. hint when filling iron with water only put small amount so water isn't laying inside when not in use.

Aug 05, 2012 | Rowenta Irons

1 Answer

Rust coming thru pores on sole plate?


You need to get a iron cleaning product to clean your machine. In the future, use ONLY distilled water in your Iron. Distilled water has been turned into steam (leaving all the minerals in the boiler) and that steam condensed back into water so it is absolutely free of minerals (that is what is coming out of your Iron).

Sum up: Clean it using a product designed to clean steam irons. Don't use tap or bottled water - ONLY distilled water.

Get the distilled water at your super market or auto parts store. Get the Iron cleaner where appliances are sold or at your local hardware store. You may have to ask for it.

Thanks for your question.

Jun 05, 2011 | Rowenta Professional DX8900 Iron

1 Answer

My iron is spitting out rust colored liquid. It is brand new. What can I do to solve this problem?


Pour the water out and refill with vinegar and let it steam all of it through the holes then fill with water and let it steam through the holes to rinse the vinegar out.

Nov 02, 2010 | Rowenta Perfect Iron

1 Answer

Dirty water in my iron


The dirty water coming out of your iron steam holes is caused by the accumulation of 'dirty' tap water: if you look inside an eletric kettle, you will see the same 'dirty' muddy brown mineral residue on the inside. In addition, if your iron is old, it can also be rust. It is a pretty common problem that can be minimized by using distilled water. You can get commercial steam iron cleaning fluid to clean the inside of your steam iron or you an simply use vinegar: 1) with a cold iron, fill the reservoir with straight vinegar 2) Place your iron on top of a metal kitchen rack above your kitchen sink, turn iron on and let it steam out all the vinegar: it should spit out the whitish mineral and muddy brown deposity. 3) Refill iron reservoir with clean water and repeat as of step 2. 4) Refill iron reservoir with clean water, wipe any dirty from the sole plate and this time on full steam, iron on clean layers of Kitchen paper to ensure that all dirt has been removed from the inside of the iron reservoir, if not, repeat from step 1 again.
In the future, try to use distilled or at least filtered water.
Hope it helps: let me know how you go!

Feb 24, 2010 | Bosch TDA8340 Iron

3 Answers

Simac Stirelli 9000 steam iron spews rusty steam and smells like burnt apples


Your steam iron has been filled with 'tap' water that may have been contaminated (thus the smell). Rust develops more rapidely in Steam Iron chambers when distilled water is not used: to clean the 'enclosure' of the steam iron from rust and smell, over a sink or outdoor, fill 'cold iron' with a 50/50 water/vinegar and a teaspoon of bicarb, let it stand for about 10 mins, then turn the iron on and let it steam the mixture out while shaking the iron gently (DO NOT BURN YOURSELF! STEAM IS HOTER THAN BOILED WATER!). Refill and Steam flush again with Clean water (distilled preferred). Repeat the steps until the rust has been completely dissolved (check by steam ironing on clean pieces of disposible kitchen paper towel. Use the Power steam or Flush function of the Iron if available. Hope it helps!

Dec 17, 2009 | Irons

6 Answers

I have a Tobi steamer, The steam is not coming out like it should how to I unclog the hose? I do know its the hose. Thank you


My wife has thrashed hers in her shop and it suddenly stopped steaming. It was about two years old. I managed to fix it. I dont think that the hose or the nozzel will be blocked because they are too wide a diameter. There will probably be a build up of silica or calicum inside. Unscrew the hose where it meets the machine. Remove the blue water tank. If you pour some water down the pipe from the end that you just unscrewed the hose , the water should well up in the depression where the tank sits through the little holes at the bottom. If it doesnt then the blockage is inside which is what I found. I used some decalcification liquid product ICL and poured it in from the hose end and let it soak for 10 minutes. Then I got a thin plastic tube to go in and scrape around as far as you can from the hose end. A thin bottle brush or pipe cleaner would be good. I then used a thin piece of wire to poke around the slits in the other end( depression) Then I emptied it out and continually flushed it through with water and give it a good shake holding your hand over the hose end connection hole. I found that when I emptied the water out , it contained all this silica and residue. I would have got about a teaspoon full in total. After several goes the blockage suddenly cleared itself and I found that suddenly the water was running through freely and welling up as described. I kept doing this until the gritty residue dissipated. You can hold the hose end under the tap and tilt the machine so that the water runs freely out through the depression well. I reassembled it and tried it out. Bingo just like new. Hope this helps. - Grant

Sep 30, 2009 | Irons

1 Answer

Rowenta Effective


The rust spot are probably caused by iron in your tap water. I would suggest you put a solution of half vinegar and half water into the water chamber and leave in the iron overnight.

Then switch it on to steam and holding the iron over the sink or over an old towel, the dirt (residue) comes out of the holes on the soleplate. Sometimes if the iron is badly scaled you might need to repeat the descaling.

Once complete, fill again with clean water and steam away, to flush any of the remaining vinegar out of the iron.

Depending on how often you use your iron and how much iron is in your water, you might consider performing this flush process every 2 or 3 months. It will help extend the life of your iron.

Another option is to use distilled water in your iron. Distilled water has all the minerals removed.

Good Luck!

Aug 11, 2008 | Rowenta Powerglide DM273 Iron

Not finding what you are looking for?
Krups V65 Iron Logo

Related Topics:

169 people viewed this question

Ask a Question

Usually answered in minutes!

Top Krups Irons Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18298 Answers

kakima

Level 3 Expert

96417 Answers

Are you a Krups Iron Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...