Question about Kenmore AC2044-1 Air Purifier

1 Answer

Time On Is there a way to program this filter to run all of the time

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

There should be a timer button that can be depressed to set the amount of run time desired up to 8 hours.

If you press the timer button 9 times it will return the unit to no timer control function and the display panel should show no time in it's window.

Posted on Jul 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I had a honeywell hepa air purifier 50250 given to me as a gift with no owners manual! Is there somewhere I can get one? also, there is buttons on the top, one saying check filter and the other saying pre...


http://www.honeywellpurifiers.com/ssi/pdf/honeywell/50100-200-300-manual.pdf


The Intelli-Check™ Filter Monitors will indicate replacement of the pre-filter and the

HEPA filter. Depending upon your individual usage (environment and hours used),

you may need to check and replace the filters more or less frequently.

To check Expected Filter Life Usage

When the unit is turned on, quickly press the appropriate filter monitor button. The

pre-filter light will flash up to 3 times and the HEPA filter light will flash up to 4 times,

depending upon how much expected filter life has been used.

PREFILTER:

1 flash = from new, up to 1/3 expected life used up

2 flashes = between 1/3 and 2/3 expected life used up

3 flashes = between 2/3 and all of expected life used up

Remains on = time to check/replace pre-filter

HEPA FILTER:

1 flash = from new, up to 1/4 expected life used up

2 flashes = between 1/4 and 1/2 expected life used up

3 flashes = between 1/2 and 3/4 expected life used up

4 flashes = between 3/4 and all of expected life used up

Remains on = time to check/replace HEPA filter

To RESET Filter Monitor

When the filter monitor light remains on, it is time to check/replace the filter and reset

the filter monitor, if needed. With the unit powered on, press and hold the appropriate

filter monitor button down for approximately 5 seconds until the light turns off.
Depending upon your individual usage (environment and hours
Page 6:

Mar 29, 2011 | Kaz Honeywell Hepa Air Cleaner (50250) Air...

1 Answer

How do you reset the filter reminder warning light?


Filter Replacement
Filter Replacement Indicator:
Your Defender® is equipped with a Filter Replacement Indicator located on the front
panel. Anytime this red indicator flashes, it is recommended that you call your authorized
FILTERQUEEN® Distributor to order a replacement filter. Anytime this red indicator stops
flashing and remains solidly illuminated, it is recommended that you change your filter. To
receive full benefit from your Defender® and to extend your warranty, it is strongly
recommended that you follow the filter replacement schedule suggested above. Under higher
pollution levels, your filters will need to be replaced more frequently.
The Filter Replacement Indicator is operated by filter time in use and is controlled by an
onboard timer. After 11 months of time in use of your Medi-Filter® Cartridge, the Filter
Replacement Indicator will begin to flash. It will continue to flash until the you reach 12
months of time in use, at which time the Filter Replacement Indicator will stop flashing
and remain solidly illuminated.
After replacement of your Medi-Filter® Cartridge, you must reset the Filter
Replacement Indicator's timer. When the timer has been properly reset, the Filter
Replacement Indicator will turn off.
Resetting the Filter Replacement Indicator Timer:
After replacement of your Medi-Filter® Cartridge per the instructions found on page 7, the
Filter Replacement Indicator's timer can be reset by performing the following sequence of
steps:
1 Plug unit into outlet.
2 Press power On/Off switch to the On ("I") position.
3 Allow unit to start running at low speed.
4 PRESS and HOLD both the Up and Down arrow buttons until the Filter
Replacement Indicator starts to blink.
5 Release both the Up and Down arrow buttons.
6 While the Filter Replacement Indicator is still flashing*, again PRESS and
HOLD both the Up and Down arrow buttons until the Filter Replacement
Indicator turns off.
If the steps above have been performed properly, the Filter Replacement Indicator will
turn off and not flash again for 11 months. If the Filter Replacement Indicator remains
on, repeat the steps again.
*Note that in step 6 above, the Filter Replacement Indicator MUST still be flashing when
the buttons are pressed the second time. The Filter Replacement Indicator will continue
to flash for approximately 3 seconds after the buttons are released as required in step 5 above.
Note: Under higher pollution levels, your filters will need to be replaced more frequently.
Note: To order replacement filters, call your authorized FILTERQUEEN® Distributor, or call
1-440-846-7800 for the Distributor nearest you.

http://www.filterqueen.com/pdf/defender.pdf

Mar 02, 2011 | Filter Queen Defender Air Purifier

1 Answer

My flair unit does not smell of ozone. Why ??


It properly needs the filter and interior cleaned. Especially, if it has run a long time without being cleaned. Or there is nothing in the household air at this time to trip the Ozone producing switch.

Feb 06, 2011 | Ecoquest Flair Air Purifier

1 Answer

How do you turn off the little red filter llight above the low speed indicator?


1. Plug unit into outlet. 2. Press power ON/OFF switch to the ON position. 3. Allow unit to start running at low speed. 4. PRESS and HOLD both the UP and DOWN arrow buttons until the FILTER REPLACEMENT INDICATOR starts to blink. 5. Release both the UP and DOWN arrow buttons. 6. While the FILTER REPLACEMENT INDICATOR is still flashing, again PRESS and HOLD both the UP and DOWN arrow buttons untile the FILTER REPLACEMENT INDICATOR turns off.
If the steps above have been performed properly, the Filter Replacement Indicator will turn offand not flash again for 11 months. If the Filter Replacement Indicator remains on, repeat the steps again.
*Note that in step 6 above, the Filter Replacement Indicator MUST still be flashing when the buttons are pressed the second time.The Filter Replacement Indicator will continue to flash for approximately 3 seconds after the buttons are released as required in step 5 above.

Nov 28, 2010 | Filter Queen Defender Air Purifier

2 Answers

Replace air filter warning light to reset?


1. Plug unit into outlet. 2. Press power ON/OFF switch to the ON position. 3. Allow unit to start running at low speed. 4. PRESS and HOLD both the UP and DOWN arrow buttons until the FILTER REPLACEMENT INDICATOR starts to blink. 5. Release both the UP and DOWN arrow buttons. 6. While the FILTER REPLACEMENT INDICATOR is still flashing, again PRESS and HOLD both the UP and DOWN arrow buttons untile the FILTER REPLACEMENT INDICATOR turns off.

If the steps above have been performed properly, the Filter Replacement Indicator will turn offand not flash again for 11 months. If the Filter Replacement Indicator remains on, repeat the steps again.
*Note that in step 6 above, the Filter Replacement Indicator MUST still be flashing when the buttons are pressed the second time.The Filter Replacement Indicator will continue to flash for approximately 3 seconds after the buttons are released as required in step 5 above.

Sep 30, 2010 | Filter Queen Defender Air Purifier

1 Answer

Blinking red light above the lowest setting on filter queen defender air purifier.


1. Plug unit into outlet. 2. Press power ON/OFF switch to the ON position. 3. Allow unit to start running at low speed. 4. PRESS and HOLD both the UP and DOWN arrow buttons until the FILTER REPLACEMENT INDICATOR starts to blink. 5. Release both the UP and DOWN arrow buttons. 6. While the FILTER REPLACEMENT INDICATOR is still flashing, again PRESS and HOLD both the UP and DOWN arrow buttons untile the FILTER REPLACEMENT INDICATOR turns off.

If the steps above have been performed properly, the Filter Replacement Indicator will turn offand not flash again for 11 months. If the Filter Replacement Indicator remains on, repeat the steps again.
*Note that in step 6 above, the Filter Replacement Indicator MUST still be flashing when the buttons are pressed the second time.The Filter Replacement Indicator will continue to flash for approximately 3 seconds after the buttons are released as required in step 5 above.

Sep 23, 2010 | Filter Queen Defender Air Purifier

1 Answer

V5 filter replace - how to reset red flashing light?


Hello,

So after you have replaced the V5 Cell Filter in the IQ Air, here are the steps you'll need to follow in order to reset the filter indicators:

  • At the main menu on the control panel, push the menu button 7 times until you get to the screen that says Replace Filter.
  • At the Replace Filter screen, press and hold the Enter Key until the cursor appears, and is flashing.
  • Press the UP arrow button on the keypad until you get to the V5 Cell Filter.
  • At the V5 Cell Filter screen press the Enter Key to confirm your filter reset selection. This will turn the corresponding filter LED to a flashing red light. IQAir requires that your reconfirm the filter selection to prevent inadvertently resetting the wrong filter. If you chose the wrong filter, press the menu key after pressing the enter the first time to disregard the filter change command.
  • To confirm the filter reset selection, press enter a second time, which will reset the filter life, and reset the filter hours.
You can repeat these instructions for the other two filters on your machine when it's time. Here's a link to the product manual for your IQ Air Health Pro Plus which will give you the same instructions, as well as other maintenance instructions.

http://lib.store.yahoo.net/lib/vacuumcleanerbacgs/IQAir-healthpro-plus-owners-manual.pdf

I hope that this information was helpful to you. If you were able to reset your filter, please be kind and rate the repair as helpful by clicking the thumbs up icons in the top of my repair. This is what really keeps Fixya experts continue leaving free repair solutions. Thank you very much,

Chris J.
GoVacuum

Apr 08, 2010 | IQAir HealthPro Plus Air Purifier

3 Answers

Red light won't go off


To RESET the Electronic Filter Check:
When the filter check light remains on,it is time to check/clean the HEPA-Type
filters and reset the filter check,if needed. With the unit powered on,insert the tip of a ball-point pen or
paperclip into the hole next to the LED filter check light and hold for approximately 5 seconds until the
light turns off (Fig 5). Depending upon your individual usage (environment and hours used),you may need
to check and clean the filters more or less frequently. If the HEPA-Type filters are cleaned before the filter
check light turns on,the filter check should be reset at the same time.
These cleaning intervals are intended as guidelines only. Performance of any filter media is dependent
upon the concentration of contaminates going through the system. High concentrations of contaminates
such as dust,pet dander and smoking will reduce the useful performance of the filter.
NOTE:The HEPA-Type filters are not washable.
Fig.5

May 24, 2008 | Honeywell HHT-090 Air Purifier

1 Answer

Kaz Honeywell Tower Air filter rest light


When the filter monitor light remains on, it is time to check/clean the IFD™ filters and reset the filter
monitor, if needed. With the unit powered on, insert the tip of a ball-point pen or paperclip next to the LED
filter check light and hold for approximately 5 seconds until the light turns off (Fig. 3). Depending upon
your individual usage (environment and hours used), you may need to check and clean the filters more or
less frequently. If the IFD™ filters are cleaned before the filter monitor light turns on, the filter monitor
should be reset at the same time.

May 18, 2008 | Kaz Honeywell Tower Air Purifier with IFD...

3 Answers

PURE Ion shuts off after a few moments


You need to shut it off, unplug it, and pull both the filters out at once and then plug it back in, and push both filters in at the same time, simultaneously. This will re-set it.
Also, if this continues to happen, you must vacuum the insides of the unit, aside from the filters, themselves, it can get all clogged up.
We live on a busy street and our house can get REALLY dusty, we have a older home with carpets and two cats - so our unit really has to work hard!
Good luck!

Oct 28, 2007 | Brookstone Pure-Ion UV Air Purifier

Not finding what you are looking for?
Kenmore AC2044-1 Air Purifier Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Air Purifiers Experts

Fordexpert

Level 3 Expert

5331 Answers

kakima

Level 3 Expert

96396 Answers

Michael Youngman
Michael Youngman

Level 2 Expert

156 Answers

Are you a Kenmore Air Purifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...