Question about Network Security & Firewall Devices

2 Answers

Aip ssm password recovery

Hi,
i m using aip ssm 10 asa5520, now i forget the password and tryed to recover the password of module using command "hw-module module 1 password recovery" but getting the message that software not supported.

ios ver of ips is 5.1

please guide me
regards,

sanjeev bhardwaj
sanjeev.bhardwaj@velocis.in

Posted by on

  • Anonymous Nov 11, 2008

    i have same problem, but su- root is not supported in my asa 5520

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 42 Answers

The following password recovery options exist:

If another Administrator account exists, the other Administrator can change the password.

If a Service account exists, you can log in to the service account and switch to user root using the command su - root.
Use the password command to change the CLI Administrator account's password.
For example, if the Administrator username is "adminu," the command is password adminu. You are prompted to enter the new password twice.

You can also reimage the sensor using either the recovery partition or a system image file. This will default the device.

Posted on May 09, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hw-module module 1 password-reset

Posted on Jun 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want to block URL


Hi!

Unfortunately, it's not possible with your firewall model...
You will need at least an ASA 5510 with an CSC-SSM module to filter URLs.

You can use an external URL filtering device with that ASA like WebSense/SmartFilter... For more info look here.

In case of a problem or clarification, don't hesitate to post me a reply before rejecting my answer.
If you are satisfied, rate my solution with the "thumbs" or (even better) add a testimonial.

Best regards,
Pelu.

Feb 04, 2011 | Cisco ASA 5505 Firewall

1 Answer

Does a 10 second reset on a Netgear router reset everything. Even the password on the network and so on?


it should only set the password on the router

Unfortunately, there is no way to recover a lost or forgotten password from a router or access point; you will need to reset the device to factory defaults. However, once the device is reset to factory defaults, you can use the default username ("admin") and password (either "password" or "1234" depending on your router) to reconfigure your router settings.

or

if there a small hole in the front or back of the router push a hair pin in to reset to factory settings

hope this helps

Jan 02, 2011 | NetGear ProSafe FVG318 (606449041668)...

1 Answer

Cisco asa 5500 - sh interface - reveals switch ingress policy drops - what are these ? will they slow down traffic ?


The following is an excerpt from cisco.com defining policy drops and their possible causes:

This drop is usually seen when a port is not configured correctly. This drop is incremented when a packet cannot be successfully forwarded within switch ports as a result of the default or user configured switch port settings. The following configurations are the likely reasons for this drop:

blank.gifThe nameif command was not configured on the VLAN interface.

Note blank.gifFor interfaces in the same VLAN, even if the nameif command was not configured, switching within the VLAN is successful, and this counter does not increment.

blank.gifThe VLAN is shut down.

blank.gifAn access port received an 802.1Q-tagged packet.

blank.gifA trunk port received a tag that is not allowed or an untagged packet.

blank.gifThe security appliance is connected to another Cisco device that has Ethernet keepalives. For example, Cisco IOS software uses Ethernet loopback packets to ensure interface health. This packet is not intended to be received by any other device; the health is ensured just by being able to send the packet. These types of packets are dropped at the switch port, and the counter increments.

blank.gifThe VLAN only has one physical interface, but the DEST of the packet does not match the MAC address of the VLAN, and it is not the broadcast address


Throubleshoot these and see if any of them apply to you. Thank you for choosing fixya.com.

Dec 04, 2010 | Cisco (ASA-SSM-AIP-20-K9=) Firewall

1 Answer

Password recovery


Try restarting your router. There should be a button on the back of the router that you can press with a paper clip or something. After that your password should change to something like:

username: admin
password: admin

or

username: admin
password: password

Apr 09, 2010 | SonicWALL TZ 170 SP Firewall

1 Answer

I want to delete recovery commander from my commuter


Recovery Commander™ can restore your non-booting system back to normal. It only takes a few minutes to get your system back up and running. Recovery Commander provides enhanced tracking and recovery features for unparalleled protection and can usually avoid the need to reload or re-image your system. And unlike Windows System Restore, it doesn't require you to successfully boot Windows to restore your system.

Jul 05, 2009 | Network Security & Firewall Devices

2 Answers

Messed up Bootmgr on a Nokia IP350


Have you tried the steops below

1. Get the IPSO image you want to install.
2. Copy it to an internal host capable of FTP.
3. Connect to the console on the IP130 and start it up, when you
get past the bootmanager part where it shows the prompt
BOOTMGR[1]>install then ftp or help a few other commands

4. The interactive prompts should help you figure out what to do (like assign it an IP and ftp to the server).
5. Let it install the image and reboot.

Jun 15, 2009 | Nokia IP 350 Firewall

1 Answer

LogMeIn


Actually you can't really block this one (not if the users have a clue) unless you have a content filtering solution on your network AND you are terminating your SSL connections on the content filtering device AND not allowing proxy servers.

Try blocking access to https://secure.logmein.com (but as I said - a user with a little wits will bypass you block using proxy setting on the client).

Nov 28, 2008 | Cisco ASA 5520 Firewall

Not finding what you are looking for?
Network Security & Firewall Devices Logo

Related Topics:

2,541 people viewed this question

Ask a Question

Usually answered in minutes!

Top Network Security & Firewall Devices Experts

phil

Level 2 Expert

567 Answers

john smith

Level 2 Expert

366 Answers

Sudeep Chatterjee
Sudeep Chatterjee

Level 3 Expert

3267 Answers

Are you a Network Security and Firewall Device Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...