Question about Tally T6218 Matrix Printer

1 Answer

Tallymans T6218 Printer

My printer is giving the following error: Faulty hammer voltage 1.What are the voltage settings for the printer hammer?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Simple. change your printer. put this in dustbin. - st.jimbalaka

Posted on Mar 29, 2008

  • Matata Mwas
    Matata Mwas May 17, 2011

    u aint of any help man...

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does it work for about 10-15 minutes, then stop and indicate ERROR HAMMER VOLTAGE 1?


Usually that is something wrong with the hammer bank

MRP provides IT Parts Product Supplies and Services

In rare instances it can be cabling, power distribution PCB or the main logic.

Jul 14, 2015 | Tally T6218 Matrix Printer

1 Answer

Printer Tally t6200 series is displayn an error : hammer voltage 1.


check the logic board if not one of the coils is faulty

Aug 03, 2011 | Tally T6218 Matrix Printer

1 Answer

I have a tally genicom 6312 printer which gives me hammer voltage 2 error what do i do


A high resistance coil fault has likely occurred in one or more of the hammer coils.
Note: this fault message will have been preceded by printing slow-down attempts associated with On-
The-Fly thermal monitoring of hammer bank temperature.
Check the hammer bank for defective coils.
If no defective coils are found replace the Controller Board.

Dec 31, 2010 | Tally T6218 Matrix Printer

3 Answers

Problem for lipi 6312 tally genicom line printer my printer shows an error (hammer voltage 1)


problem for lipi 6312 tally genicom line printer my printer shows an error (hammer voltage 1)

Apr 20, 2010 | Tally T6218 Matrix Printer

3 Answers

Tally Printer the error is some times Hammer


In the T6215 Maintenance Manual the fault message: Hammer Voltage has been replaced, in the T6218, with:

Hammer Voltage 1
There is a new fault message for the T6218. It is:

Hammer Voltage 2
Explanation: A high resistance coil fault has likely occurred in one or more of the hammer coils
Note: This fault message will have been preceded by printing slow-down attempts associated with On-The-Fly thermal monitoring of hammer bank temperature.

Corrective Action:
Check the hammer bank for defective hammer coils.
Confirm that hammer drive board is functioning properly.

Apr 05, 2010 | Tally T6218 Matrix Printer

4 Answers

The 6306 L showing HAMMER VOLTAGE 1 ERROR WHAT SHOULD I DO


ERROR IS BECAUSE OF DRIVER IC FAULTY IN LOGIC CARD
PLZ CHANGE THE HAMMER DRIVER IC IN LOGIC CARD

Dec 13, 2009 | Tally 6306 Matrix Printer

1 Answer

Tally 6218 hammer voltage 2


Hammer Voltage 2 is the worst error you can get on the Tally T6200 series...

Explanation:
A high resistance coil fault has likely occurred in one or more of the
hammer coils.
Note: This fault message will have been preceded by printing slow-down
attempts associated with On-The-Fly thermal monitoring of hammer
bank temperature. Check blower underneath ribbon Deck.

Corrective Action:
Check the hammer bank for defective hammer coils qty 7 per hammerbank.
Confirm that hammer drive board is functioning properly.
c19596d.jpg

Aug 25, 2009 | Tally T6218 Matrix Printer

1 Answer

I have T6218 printer and it prints for about TWO minutes then starts slowing down and then stops printing showing an error of "HAMMER VOLTAGE 2". I relaced the Hammer coil kit in Banks 1 and 2. still same...


If you haven't fixed? If you don't get Hammer Voltage 2 error immediately, then sounds like your blower underneath the ribbon deck which keeps the hammerbank kewl is not working... Be careful but you can get shelf or cart about printer height and remove the ribbon deck with ribbon & cables still connected from the print. Rotate and sit it on the shelf or a cart. Start printing and see if the black blower(in the middle with a little black air duct going to the hammerbank) is working.

One other thing their's qty 7 hammer coils per hammer bank, if you have replaced the 1st 2 reading from left to right with hammerbank installed in printer, then you have qty 5 more which 1 of the 5 left is causing Hammer Voltage 2.

Have any other ??? feel free to call at x311
Toby

Feb 02, 2009 | Tally T6218 Matrix Printer

1 Answer

Showing hammer voltage 2 error


the problem comming from logic board. need to change the logic board and hammer bank cable at the same time.

Apr 05, 2008 | Tally T6218 Matrix Printer

2 Answers

Hammer voltage 2


it prints for about two minutes then starts slowing down and then stops printing showing an error of : hammer voltage 2

Sep 05, 2007 | Tally T6218 Matrix Printer

Not finding what you are looking for?
Tally T6218 Matrix Printer Logo

Related Topics:

222 people viewed this question

Ask a Question

Usually answered in minutes!

Top Tally Printers & Copiers Experts

Toby
Toby

Level 1 Expert

34 Answers

Tony

Level 3 Expert

2598 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Tally Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...