Question about RCA 27F530T 27" TV

1 Answer

No picture, but power light is on

When I turn on the tv, the power light comes (you can hear normal click sound), then immediately following it, nothing - no picture.

Before this occured a day before, I was watching tv, the screen blinked, then a few seconds later, it went off. Turned off the tv, waited a few minutes, turned it back on and everything was fine. Did it again, repeated the steps. Now, nothing, just the power light comes and nothing, however, if I do press the channel button up, I can hear sound but no picture, but when I put it back on the channel 3, because I have a dish, no sound or picture. Any suggestions...

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 85 Answers

THE POWER SUPPLY OF YOUR TV WAS THE PROBLEM,YOU COLD SOLDER THE MAINBOARD OF YOUR TV,AND THE CRT SOCKET CONNECT TO THE TUBE IS ALSO COLDSOLDER,.

Posted on Jun 19, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sansui HDLCD 3200 TV not powering on.


There is a problem with tuner module, try connecting with DVD if normal then the easiest way is to replace the tuner module

Nov 12, 2016 | Sansui Televison & Video

2 Answers

Maxent MX-42HPM20 won't turn on


i have the same thing but what i do is unplug the tv and plug again till i hear a click then replug immediately and wait for the tv to come on .this is normally a symptom of a weak surge protector in the back, inside of the tv.it is normally not an expensive repair and better still if the tv is still on gaurantee it should cost nothing.

Nov 21, 2011 | Maxent MX-42HPM20 42 in. Plasma HDTV

1 Answer

No picture on my philips 42PF7321D/37


Bad caps in the power supply must be replaced .

Jul 21, 2009 | Philips 42PF7320A 42 in. Plasma HDTV

1 Answer

No picture or audio.power light blink on once and turns off


The real deal here is the protection circuit has activated. This is caused whenever an excessive amount of current is being drawn from the main power supply. Upon detection of same, it immediately takes over the power management of the set and shuts it down. The clicking sound you hear is the ON relay turning on the set, but immediately the power mangement system shuts it OFF. You should hear two clicks, but they may be so close together that it sounds like one click.

This set is getting rather ancient and I would not recommend you spend much money on it for this reason: It is highly likely that once the set if repaired that another failure would occur. This is because of the law of averages; the first failure is often followed by another failure from anywhere within the set.

May 31, 2009 | Toshiba Televison & Video

1 Answer

Plasma Hyundai 42'' TV ,NO SOUND OR PICTURE


most times then not it's the capacitors on your power board that blew there for not supplying the tv with enough power if you open it up and check the capacitors it should be leaking some kind of liquid or the tops have bubbled up. its an easy fix cost>>2 dollars each

May 21, 2009 | Televison & Video

1 Answer

NO PICTURE, NO SOUND On My Plasma TV.


Should have been 3300 UF 10V caps that were bad? Shouls have been replaced with 3300UF 18V. 50V is huge. If it was replaced with a 50 the polarity may be wrong or the cap it too big to be seated property. Sometimes the caps just dry out and even a normal looking one will be the culprit of no OSD. Are you getting an LED fault code blinking? That should be a red led. Do you hear the relay clicking.? When you replaced the caps did you charge them? Just plugging in the set without trying to power it on for about 20-30 mins. I may be able to help you

gysgt2u1@yahoo

Mar 05, 2009 | Philips 50MF231D 50 in. Plasma Television

1 Answer

Startup Problem with my 42pf7321d/37 Phillips plasma TV


I need to know how long do you have the tv?In the other word,approx. how many hours you have put into it?
Secondly,did you wall mounted the tv or setting it close the the area which there is not much room for the back of your tv to breath?
solutiondoct

Nov 06, 2008 | Televison & Video

3 Answers

No picture, no sound.


Hi i have a pilips 42" plasma tv (42PF5320/79) i can hear clicking the green light is on and the tv will go into stand by if i press the power button and the red light also comes on .I have turned it on and off and it works now nothing just the light on the front as if its working looking at the back through the slots two green lights come on then the tv clicks and they turn off,thanks

Aug 06, 2008 | Philips 42PF9630A 42 in. Plasma Television

Not finding what you are looking for?
RCA 27F530T 27" TV Logo

Related Topics:

465 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Televison & Video Experts

The Knight
The Knight

Level 3 Expert

70943 Answers

matt martin
matt martin

Level 3 Expert

1207 Answers

Jaime Hernandez

Level 3 Expert

2270 Answers

Are you a RCA Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...