Question about Televison & Video

2 Answers

Install motherboard drivers for the first time

I just replaced my motherboard with a 662mx foxconn but im not able to boot my computer , it just restarts itsself after the post

i just bought a motherborad 662mx. the problem i had is, i can't install wins xp. when every time i try to install, the wins show up and said this file can't copy. i don't know how to fix it. i spend alot money for nothing. please can everyone who know what's going on and can tell me the problem is.

Posted by on


2 Answers

I don't know how to set up boot priority. can you tell me how to do. thank you

Posted on Mar 13, 2008

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 807 Answers

If you have a genuine copy of XP then it should boot from that and install it. If it's not booting from that you may have to change the boot priority in the bios, the motherboard manual will tell you how to enter the bios and make and save changes.
Are you sure it's not trying to boot from the hard drive.
As for the motherboard drivers they are installed after you put XP on.
If it's not reading the XP CD properly you may have a bad CD or CD Rom.

Posted on Mar 13, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How can i get schematic . diagram of foxconn 662mx

take a look at their support page, if you contact them directly they may be happy to assist

Jul 08, 2015 | Foxconn Computers & Internet

1 Answer

After instal of pci-e graphics card it goes into reboot cycle??

Hi Paul, try to pullout the card and used on-board graphics. if it works without rebooting, the cards need to be replace.

Jan 10, 2014 | Foxconn G31MX-K socket LGA775 motherboard

1 Answer

Updated drivers

try visit this page "" may it can solve your problem

Mar 24, 2013 | Foxconn Bios Chip:45cmv-k 45cmx 45cmx-k...

1 Answer

Cannot get computer to boot, loops foxconn logo refuses to boot. Tried reinstalling windows 7, crashes. tried from usb flash drive and dvd. The drive lets me install windows and works from another comp....

When this happens, it is either a driver issue, or the Hard Drive is bad. You need to try to bootup in safe mode, F8 at boot time. select, boot to safe mode desktop, IF it boots to this, i think, you may need to install the most up-to-date Video driver, in fact, you should, obtain and have at hand ALL drivers for your MB, and add on's/ This way you can install, in a s situation such as this. Store on a USB drive, and install them off this. Now if you cannot, access F8 or the PC, you need to get into the BIOS, set to boot from DVD, Boot from the Windows, install DVD, now perform a FULL FORMAT, and then try an install, if this doesn't work, either your install disc is corrupt, or the hard Drive is, i would suspect, first the Install DVD and then the HDD, you need to swap out a HDD to check. It may also be a piece of hardware attached too, again swapping out is the only way to track down a problem

Apr 04, 2010 | Computers & Internet

2 Answers

Need raid pata driver for foxconn rc4107ma motherboard

Normally RAID setup on board, is handled in the BIOS settings.

Feb 21, 2010 | Computers & Internet

2 Answers

MEMORY UPGRADE FROM DDR 256Mb to DDR2 1GB hangs when Log on/Booting

Its a memory problem obviously. Try dusting the memory slot and try inserting the memory into the slot a couple of times. If still not working, the memory may be incompatible(rarely, there are brands of boards that doesn't suit to certain brands of memory), or it may be damaged.

Sep 27, 2008 | Foxconn P4M800P7MA-RS2 Motherboard

1 Answer

Install motherboard drivers for the first time

did u format your hard drive with new mobo ? resisnatll it all then defult bios rechesk all settings in there

Jan 19, 2008 | Foxconn (945G7MA-8KS2) Motherboard

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

75767 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers


Level 3 Expert

81400 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides