Same as jasonvonk mar 15 2010 I get error code 37 after device and menu buttons pushed. red lite blinks 4 short pause and 4 short again Jim

It is helpful to have the sequence of the blinking red light. This may help:

MODELS: WD-52627 / 52628 / 62627 / 62628 / 62827 / 62927 / 73727 / 73827 / 73927

Page 43

3. Error Code Operational Check

Note: The TV must be in "Shut Down" and not have been switched Off, to perform the Error Code Operational

Check. When the TV is switched Off, the code automatically resets to "12" No Error.



Pressing the front panel "DEVICE" and "MENU" buttons at the same time, and holding for 5 seconds,

activates the Error Code Mode. The LED flashes denoting a two digit Error Code, or indicating no problem

has occured since the last Initalization.



Note: The front panel buttons must be used, NOT those on the Remote Control.



• The number of flashes indicates the value of the MSD (tens digit) of the Error Code.

• The flashing then pauses for approximately 1/2 second.

• The LED then flashes indicating the value of the LSD (ones digit) of the Error Code.

• The Error Code is repeated a total of 5 times.



Example: If the Error Code is "23", the LED will flash two times, pause, and then flash three times.



4. Error Codes

The Error Code designations indicating malfunction, or no malfunction, are listed below:

POWER

LED

STATUS

LED

LAMP

LED

Power

Status Condition

Off Yellow Off Low

Power Excess heat. Check Lamp Filter

Off or On Off Yellow No

change

120w usage time over 7000 Hrs.

150W usage time over 3500 Hrs.

Off Off Blinks

Yellow

Low

Power Lamp Cover open

Off Blinks

Yellow Off " Filter Cover Open

Off Off Red Stby Lamp did not turn On

Off Blinks

Red Off Low

Power Fan Stopped

Off Red Off " Circuit failure (short or DVI

connector unplugged)

Abnormal LED Indications

Error Codes "DEVICE" & "MENU"



Error Codes Description



12 No error detected

22 Recovery from Reset

32 Lamp cover is Open

34 Lamp abnormality

35 DM Fan failed (Chassis Fan)

36 Exhaust or Lamp Ballast Fan failed

37 DMD Engine Fan failed

38 Lamp temperature abnormally high. Remove Lamp to check filter.

39 DMD temperature abnormally high

41 Short is detected (Standby Power Supplies)

42 Lamp Fan failed

44 DVI cable between Format and Engine disconnected

46 DMD Temp. Sensor not detected (check DT connector))

47 DM Temperature too high

48 Engine power supply short detected

51 Speaker Drive circuit short detected

52 HDD excess temperature (V30+ & V31 only)

55 HDD Fan Stopped (V30+ & V31 onlyt)

When the status light is blinking push the device and menu buttons on the tv at the same time and hold for 5 seconds or more. The red light will then blink a code. It will blink like 3 times, pause, then blink like 5 times. That would be a code of 35. It may blink one time long, then two short blinks. That is not a code blink but indicates another problem. Do a search for the service manual for your tv on the internet and look up the code. Sometimes it is as simple as a dirty fan that won't turn any more. But by knowing the codes you will know if you need a technician or if it is something simple.

Please listen and try this:

When the power light comes on and goes off, on the front of the set press BOTH the Menu and Input (Device) buttons at the SAME time and HOLD them both for at least five seconds and then release both.

The power light will blink a two digit error code and will repeat it about 5 times. To get it to repeat you would have to unplug the set and turn it on again etc.

The most common error is 2 blinks, pause, 2 blinks.

Let me know what error code you find and I will direct you as to what it means and what may have to be done.


SD TECH

Those blinks are fault codes. To know more visit the site linked here. http://electronicshelponline.blogspot.com/

push the menu and device buttons on the front of the set both in together and hold for 6 seconds and see what two digit error codes blinks. It will most likely blink a 3 pause then 4 and then repeat the sequence indicating a 34 error for lamp abnormality which is almost always caused by faile capacitors on the Power pwb.

The TV indicates an error code 22 (short circuit protection). Check 2 STK392-570 convergence IC for shorts and 5amps pico fuse for open. I usually replace both STK's.

THAT IS A CODE 44 RIGHT FRONT PRIMARY AIR BAG SENSOR TO PRPERLY MOUNTED TO VEHICLE

the status light blinking red means a fan (the unit hs 4 of them) has failed. you need to determine which one. use the self diagnostic function:
Error Code Operational Check
Note: The TV must be in “Shut Down” and not manually switched Off, to perform the Error Code Operational
Check. When the TV is switched Off, the code automatically resets to “12” No Error.
Press the front panel “DEVICE” and “MENU” buttons at the same time, and hold for 5 seconds to
activate the Error Code Operational Check. The LED will then flash denoting a two digit Code.
Note: The front panel buttons must be used, NOT those on the Remote Control.
• The number of flashes indicates the value of the MSD (tens digit) of the Error Code.
• The flashing then pauses for approximately 1/2 second.
• The LED then flashes indicating the value of the LSD (ones digit) of the Error Code.
Example: If the Error Code is “32”, the LED will flash three times, pause, and then flash two times.
• The Error Code is repeated a total of 5 times.


and read the code.
35= Chassis Fan failure
36 =Exhaust (Back Cover) or Lamp Ballast Fan failure
37= Engine (DMD or Lamp) Fan failure

contact www.wehavepart.com 1-800-575-9833 for the part and see how much it cost. Or www.advancebaldwin.com or www.andrewselectronics.com./

Mitsubishi TV troubleshooting
Here's something that might also be useful. After you turn on the set, and get the regular red blinky lights, hold down the Device and Menu buttons together for about 5 seconds.
The Power light will start to flash in a two digit sequence.
For example, 3 flashes, then 7 flashes = 37.
Here are the error codes, and the corresponding problem:
12 = No error detected, check power supply.
32 = Lamp Cover is open.
33 = Air filter cover is open.
34 = Lamp abnormality
36 = Light Engine (DMD or Lamp Fan stopped)
37 = Exhaust or Lamp Ballast Fan stopped
38 = Lamp Temperature High
39 = DMD Temperature High
41 = Short is detected
44 = DVI cable between FMT and Engine disconnected