Question about Mmats D500.2 Amplifier Car Audio Amplifier

1 Answer

Mmatsd500.2 ok what would my best bet be i know a guy who has 3brand new mmats procast 12s would it be best to get one of them&run with the 15w6 or add one to 15w0 8ohms two that i have&also i have a ppi4200am series&old alpine3553amp with 2sets of mbquart 6.5r series i plan on running in my tahoe what would the best way to run all this set up i have know idea of the power the 3553 puts out any help is highly appreciated thanks BATMAN what would the best way to hook these all up

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 290 Answers

First, the specs:

  • PPI 4200am = 50x4 at 4 ohms, 100x4 at 2 ohms
  • Alpine 3553 = 35x4 at 4 ohms, 50x4 at 2 ohms
  • Mmats D500.2 = 350x1 at 4 ohms, 500x1 at 2 ohms
  • 3x Mmats Procast 12 = Dual 4 ohm VC
  • 1x JL 15w6 = Dual 6 ohm VC
  • 2x JL 15w0 = Single 8 ohm VC
Second, I don't think I would recommend mixing n' matching the subs. One of the subs would always be working harder than the rest. If you want to run multiple subs, make them all the same. Sometimes, you can get away with it if they are all the same voice coil impedance, but in this case you've got dual 4 ohm, dual 6 ohm, and single 8 ohm subs all in the mix.

If it were me, I'd probably stay with the single 15w6. But it's your money :)

Posted on Mar 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Every time i power up my mmats d800.2 it goes straight to protect not sure why? anybody knows what the problem can be?


just try to find any of Ur speaker using is not well by removing one by one it will work again .use the same recommended impedance speaker and do not overload the output channel .hope it will work normal if any damage or short is not happened inside.first remove all the wires of speakers and pull out the power cord also .

Apr 15, 2013 | Mmats Car Amplifiers

1 Answer

My Mmats 3000.5 mono block amp keeps going into protection, without a load. Any ideas why? The brand is Mmats pro audio. the next page does not list this brand.


If an amp has no load, as in there are no speakers connected to it, then it will go into protection mode because it sees an infinite load. Be thankful that it has a protection mode, or it would be toasted!

Feb 15, 2012 | Car Amplifiers

1 Answer

I need to know the output transistor for mmats d200hc


You need the schematics first - do not blindly determine where they are.

Jan 29, 2011 | Car Amplifiers

1 Answer

Need to know how to wire my system ...I have the infinity reference series 611a I was told it was a mono block but it has two channels on the exterrior...also I have two 12 inch MTX thunder dual voice coil...


it all depends on what kind of box the mtx subs are in as far as wiring the subs. The best way would be take the speaker wire from both sub boxes and run the positive into the right positive then the negative into the left negative. and run 8 gauge wiring kit to the amp because 10 might be to small and 4 is to big 8 gauge is perfect for this amp.

Jul 18, 2010 | Infinity Reference 611a Car Audio...

1 Answer

My mmats car amp goes into thermal


remover cover check your capacitors. if the top is bubble out there blown, they can be replaced by sodering a new one on. also just visually inspect all components in amp

Jun 09, 2010 | Car Amplifiers

1 Answer

How would i know if im getting the max out of my 3 orion pros 12s


check out audiobahn.com under tech support it will show you all the wiring diagrams

Apr 10, 2010 | AudioBahn A2300HCT Car Audio Amplifier

1 Answer

Amp and speaker wiring


if the 12's are single 4 ohm coils then i would run them parrelle to the amp bridge to one channel. this will be 2 ohms bridge and will be the best and most power.

Jan 29, 2010 | Autotek SS500.1 Car Amp

1 Answer

Sub Selectroin


try to find a the specs for a box for those subs. A box has a great deal to do with highs, mids and lows.

Jan 09, 2009 | Car Amplifiers

1 Answer

Mmats d500.2


  • It is capable of driving a 2 ohm load.
  • It is a single channel amp, so bridging is not applicable. There are two speaker connections, true, but they are tied together internally.
  • It's rated at 500W @ 2 ohms
  • The issue you're going to have hooking up the subs you own is that you're not going to be able to optimize the output of the amp. If you hooked all of them up in parallel (both 15w0 as well as the dual voice coils of the 15w6), you'd be putting a 1.7 ohm load on the amp, which it may not like. In my mind, your best bet is to either put both 15w0's in parallel (125W per sub) and not use the 15w6.....OR.......use only the 15w6 with the dual voice coils in parallel (350W to the sub).

Mar 12, 2008 | Mmats D500.2 Amplifier Car Audio Amplifier

Not finding what you are looking for?
Car Amplifiers Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mmats Car Amplifiers Experts

Tygh Duval
Tygh Duval

Level 2 Expert

290 Answers

Pablo Gonzalez

Level 3 Expert

733 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Are you a Mmats Car Amplifier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...