Z4mplus Printer Idle V60.13.0.10 Error Condition HEAD OPEN Power in Yellow color Pause in Orange color Error in Orange color Data in Yellow color Please help

Please try to open the head full until it has contact with the magnet on the inner side of the housing, than close again and press pause key to release printer from pause mode. If calibration is activated, the printer should calibrate afterwards.

However, if there are further things and you are looking for the manual you will find it here:
http://www.servopack.de/support/zebra/Z4Mplus_Z6Mplus.pdf

Issue: Alarm / Power light flashes orange 5 times consecutively (Print Head / Cartridge Error)
Solution: Reseat the print head iP3000

Reseat the print head

1. Confirm that the printer is powered on.
   
   
2. Open the paper output tray and top cover.
   
   Note: Gently open the paper output tray while holding it.
   
   
3. After confirming that the print head holder has moved to the center, open the inner cover.
   
   
4. Remove all ink tanks
5. .Raise the print head lock lever and remove the print head.Re-seat the print head into the print head holder and lower the print head lock lever until a click is heard.Insert the appropriate ink tank into the slot at the right end and push down on the PUSH mark on top of the ink tank until a click is heard. Install the other ink tanks in the same manner.Close the inner cover and top cover.Properly installed: Note: Check that each ink tank is installed in the correct position

Issue: Alarm / Power light flashes orange 5 times consecutively (Print Head / Cartridge Error)
Solution: 2 Reset the printer

Resetting the Printer By resetting the printer's power, the print buffer is cleared and certain sensors are reset. If there is invalid data in the buffer, or sensors are stuck in a particular mode; errors may occur. Follow these steps to reset the printer:

1. Turn the printer off with the Power button (if available).
   
   
2. Disconnect the data cable from the printer (not applicable to WiFi, Bluetooth or Infrared) .
   
   
3. Unplug the printer's power cord for approximately 10 minutes, and then plug it back in. If troubleshooting a communication issue, reconnect the data cable (not applicable to WiFi, Bluetooth or Infrared).
   
   
4. Turn the printer back on.

Close the head and be sure that it is latched. Then take the printer off pause to clear the error.

Issue: Alarm / Power light flashes orange 5 times consecutively (Print Head / Cartridge Error)
Solution: Install the print head and ink tanks correctly iP4500
Reseat the Print Head and ink tanks iP4500
Follow these steps to reset the printer:

1. Turn the printer off with the Power button (if available).
   
   
2. Disconnect the data cable from the printer (not applicable to WiFi, Bluetooth or Infrared) .
   
   
3. Unplug the printer's power cord for approximately 10 minutes, and then plug it back in. If troubleshooting a communication issue, reconnect the data cable (not applicable to WiFi, Bluetooth or Infrared).
   
   
4. Turn the printer back on.

After closing the head, it will display "HEAD OPEN" until you push the pause button (the pause button will be blinking too). Try it and let me know!

check the setings, change the setings, Media TYPE from Termal Transfere to Direct Termal.
if necessery, reset the printer to Factory Defult.

The first mainboard of Z4Mplus falls short of this error and need replacement.
Roberto Martinez

Secret Guitars

• Snaketapus Guitar: Complete Hard Mode.
• The Log" Guitar: You must achieve 5-Star every song on Expert.
• Battle Axe Guitar: Complete Expert Mode.
• Casket Guitar: Complete Medium Mode.
• Eyeball Guitar: You must achieve 5-Star every song on Hard.
• Fish Guitar: Complete Easy Mode.
• USA Guitar: You must achieve 5-Star every song on Easy.
• Viking Guitar: You must achieve 5-Star every song on Medium.

Unverified. On the main menu, directly depress the colored key without any other input.

Performance Mode ... YELLOW, YELLOW, BLUE, YELLOW, YELLOW, ORANGE, YELLOW, YELLOW
Hyper Speed ... ORANGE, BLUE, ORANGE, YELLOW, ORANGE, BLUE, ORANGE, YELLOW
Air Guitar ... YELLOW, YELLOW, BLUE, ORANGE, YELLOW, BLUE
Eyeball Heads ... BLUE, ORANGE, YELLOW, ORANGE, YELLOW, ORANGE, BLUE
Moneky Heads ... ORANGE, BLUE, YELLOW, YELLOW, ORANGE, BLUE, YELLOW, YELLOW
Flaming head ... ORANGE, YELLOW, ORANGE, ORANGE, YELLOW, ORANGE, YELLOW, YELLOW
Horse head ... BLUE, ORANGE, ORANGE, BLUE, ORANGE, ORANGE, BLUE, ORANGE, ORANGE, BLUE
Hyper Speed ... ORANGE, BLUE, ORANGE, YELLOW, ORANGE, BLUE, ORANGE, YELLOW
Air guitar ... BLUE, YELLOW, ORANGE, BLUE, YELLOW, YELLOW
Eyeball Heads ... YELLOW, ORANGE, BLUE, ORANGE, BLUE, ORANGE, YELLOW
Hyper Speed ... YELLOW, ORANGE, BLUE, ORANGE, YELLOW, ORANGE, BLUE, ORANGE
Monkey Heads ... YELLOW, YELLOW, BLUE, ORANGE, YELLOW, YELLOW, BLUE, ORANGE
Flaming Head ... YELLOW, YELLOW, ORANGE, YELLOW, ORANGE, ORANGE, YELLOW, ORANGE
No HUD performance mode ... YELLOW, YELLOW, ORANGE, YELLOW, YELLOW, BLUE, YELLOW, YELLOW

Horse Head ... BLUE, ORANGE, ORANGE, BLUE, ORANGE, ORANGE, BLUE, ORANGE, ORANGE, BLUE, ORANGE, ORANGE, BLUE, ORANGE, ORANGE, BLUE, ORANGE
To unlock everything in the game, insert the following code on your guitar at the title screen: Blue, Yellow, Orange, Red, Orange, Yellow, Red, Yellow, Red, Yellow, Red, Yellow.

Search Results for ORANGE 5 AND GREEN 1 <<Previous 30 results Next>>
1. Power light (or Alarm and Power lights) alternate(s) between orange and green
After long green flash, there are 2 or more alternating orange and green flashes. There may also be a Service Error message on the computer screen. 2. Alarm / Power light flashes orange 11 times consecutively (Automatic Print Head Alignment Error) 3. Alarm / Power light flashes orange 2 times consecutively (Load Paper / Paper Feed Error) 4. Alarm / Power light flashes orange 3 times consecutively (Paper Jam Error / Cover Error) 5. Alarm / Power light flashes orange 4 times consecutively (Out of Ink Error) 6. Alarm / Power light flashes orange 5 times consecutively (Print Head Error)
#1 & #6 seem to be as close as I can find:
here is the page (Below) if you just put the error in the space provided.

http://www.usa.canon.com/consumer/controller?act=ModelInfoAct&tabact=SupportDetailTabAct&fcategoryid=257&modelid=10239

try to move the silver plate (under the printhead) up a litle bit.
this silver plate is the "print head open, and the media sensor.