Question about Samsung CLP-500N Laser Printer

1 Answer

Main Motor Error

When I start my printer (CLP-500) it initialises and says "ready" . . . then 5 seconds after saying ready, it come up with the message "Main Motor Error". Do you know what part needs replacing?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

I'm stepping out on a limb, but I bet it will be the Main Motor. samsungparts.com

Posted on Oct 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

CLP-315 - CLP-315 Laser Printer: Printer says it is online and ready to print. All ...


Hi,

you may want to run a repair on the printer driver. by going to windows START -> all programs -> Samsung CLP 310 -> Maintenece - > repair and follow the onscreen next till finish.

this could help some time when you swap USB cable or port or PCA main been replace or updated.

May 17, 2010 | Samsung CLP 315 Laser Printer

1 Answer

Samsung CLP 500 Error message 'Replace transfer roller'


You need to enter the hidden engineer menu: turn the printer off then turn on again whilst holding down the enter key on the control panel. It should say something like EDC menu on the display and you can scroll through several menus to find the one about resetting counters. Be careful not to play with other options as you can screw the printer up if you don't know what you're doing!

Mar 31, 2009 | Samsung CLP-500 Laser Printer

1 Answer

Error Jam0 in tray1


GO ON LINE TYPE IN MANUFACTURE NAME,MODEL#, ERROR MESSAGE AND ENTER KEY LIKE THIS:
CAMSUNG CLP-500 LAZER PRINTER ERROR MESSAGE JAM0
ENTER

ROD

Feb 09, 2009 | Samsung CLP-500 Laser Printer

1 Answer

Hello my printer says there is a waste motor error where is the motor found?


remove the waste container..front of the printer.
remove the casing..lower area, you will see a wee motor.
more than likely, use a vacuum to unclog the waste auger.

Dec 10, 2008 | Samsung CLP-500 Laser Printer

3 Answers

Dev motor error Samsung CLP 500


the transfer belt maybe defective or run its course..end of life
go into the menu, and see what the setup tells you

Oct 26, 2008 | Samsung CLP-500 Laser Printer

3 Answers

RICOH 2015 error code sc 500


Main motor/ transport motor lock/ fusting motor error.

The only thing you can do is check for any obstructions in the machine.

That needs to be looked at by a service because the problem could be a motor, a pcb, or a power supply.

It can be a lot of troubleshooting to do.

Oct 18, 2008 | Ricoh Aficio 2015 Copier

1 Answer

Waste Motor Error message on Samsung CLP-500


This error is caused by the Waste Toner Motor 'stalling' - usually as a result of the Waste Toner Full message being ignored for too long, and the waste system becomming overful.

Usually best to replace the Waste Toner Motor assembly.

They are for sale on auction websites from time to time.

Sep 12, 2008 | Samsung CLP-500 Laser Printer

1 Answer

Low heater error


I bought another second hand one for € 40,00 and replaced the unit. It's just 5 screws and on we go again.

I have a CLP 500 and bought a CLP510N. The units are the same. unfortunately not all parts on the machine are the same, but for now mine works again.

May 21, 2008 | Samsung CLP-510 Laser Printer

4 Answers

Hp laserjet 1320 problem


This is an error state that is not described at HP site.

Try to do a hard reset:

1) Turn off the printer

2) Press and hold down the green GO button

3) Turn the printer on and continue to hold the green GO button for at least 5 seconds, but not longer than 15 seconds. During the process, the Attention LED will turn on.

4) Release the GO button.NOTE: If both the Attention light and the Ready LEDs turn on before the GO button is released, the cold reset procedure must be started over at step 1.

5) The printer LEDs begin cycling. The cold reset process runs until completion and the printer returns to the Ready state.

Hope it will help you

Jan 24, 2008 | HP LaserJet 1320 Printer

3 Answers

Samsung CLP-500 error


Machine needs fuser replaced, normal user changable consumable, about 200 bucks in Oz

http://www.precisionroller.com/manufacturers/samsung-clp500.html

Nov 06, 2007 | Samsung CLP-500 Laser Printer

Not finding what you are looking for?
Samsung CLP-500N Laser Printer Logo

Related Topics:

352 people viewed this question

Ask a Question

Usually answered in minutes!

Top Samsung Printers & Copiers Experts

Whit
Whit

Level 1 Expert

185 Answers

HEMANT GROVER

Level 2 Expert

166 Answers

sureshd2008

Level 1 Expert

25 Answers

Are you a Samsung Printer and Copier Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...