Question about Whirlpool Duet GHW9150P Front Load Washer

4 Answers

JUST STAYS IN CYCLE AND DOES NOTHING

MY WASHER STARTED NOT DRAINING COMPLETELY, ON THE NEXT WASH IT STAYED IN CYCLE, WATER CAME IN AND IT SOUNDED LIKE IT WAS WASHING BUT THE DRUM DID NOT TURN. I TRIED IT IN SPIN AND AFTER A FEW MINUTES IT TURNED 3 TIMES THEN NOTHING. IT IS STILL JUST SITTING IN THE SPIN CYCLE. ANY IDEAS?

Posted by on

  • lapaille May 15, 2008

    I cleaned my filter - and it needed it - but it will not spin - goes through all the other cycles but does not spin - any help would be appreciated.

    Whirlpool front loadeer - DUET

  • Anonymous Mar 22, 2014

    It must stop and start 50 times while trying to complete a cycle, which it does after a few hours

×

Ad

4 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 97 Answers

Hiya
the filters are usually located behind the plastic kick plate on the front of the machine or behind a flap also on the front of the machine.
if the filters are all clean then it maybe that the motor brushes are worn down and so the machine wont spin
it could possibly be a faulty pressure switch not telling the machine that the water has completely gone and again wont spin.

hope this helps


please dont forget to rate the helpfulness of this reply thanks kj

Posted on Aug 03, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Where are the filters??

Posted on Mar 30, 2008

Ad

Pull off the front panel and emty your filter to the pump

Posted on Mar 12, 2008

Try cleaning out the filters

Posted on Mar 12, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Washer not washing?


SADLY WE SOMETIMES HAVE TO CALL THE REPAIRMAN oops did not want caps .

Sep 22, 2015 | Washing Machines

1 Answer

Zanussi zwf1421


Thermostat or heater most likely causes. Does timer button move round without doing anything? Timer knobs on Zanussi notorious for breaking off inside.

Apr 28, 2012 | Zanussi F1245W Front Load Washer

1 Answer

Washer makes a steady thumping sound


Could be coin in pump hitting blades...Try pump only no spin this will discount the drum ....Check filter if you have one.

Apr 08, 2010 | Washing Machines

1 Answer

Washing machine wont hold water on any setting


raise the main drain hose to the top of the back control head. there may be a problem with the main hose being to low and the water is gravity siphoning out of the washer.make sure the washer is off when you lift the hose up but do not remove it from the wall,you should here water drain out once it has stopped draining restart you machine and it should fill to the proper level and quit then go into your wash cycle

Jan 31, 2010 | Whirlpool Inglis IP4400 Washer

1 Answer

My washing machine got to the spin cycle but didn't drain water


prolly cuz you didnt check your pockets first and either change or a set of keys fell out

Aug 15, 2009 | Washing Machines

1 Answer

Kicking out water during wash cycle - spin instead of agitation


Hi,
Try these

  1. Check the drain hose, it should be at least as high as the top of the wash tub, about 38 inches.
  2. The drain hose must sit loosely in the house drain. Do not seal the air gap around the drain hose or a siphon will occur.
  3. Check the drain control lever
  4. Test the drain control coils
  5. Check the cam bar
pls rate my suggestion..

Jul 19, 2009 | Maytag LSE7806A Top Load Stacked...

1 Answer

Washer constantly draining after first cycle


For the machine to keep filling it would indicate that there is a siphoning problem. Check the outlet hose is not running along the ground, it has to rise up then loop back down or the water will just run straight down the drain. If the problem only happens after the first pump out it would indicate the end of the outlet hose is lower than the drum or there is no air break around the outlet hose. (The stand pipe should be larger in diameter than the hose from the machine).
http://selfix-uk.co.uk/under%20sink%20plumbing.html

May 01, 2017 | GE Spacemaker WSLP1100D Top Load Washer

2 Answers

Washer won't drain and clothes stay soaked


Can you give me a model and brand name. Does the washer drain at any time during the wash cycle?
Will it go into a spin at all in any setting? heavy duty, normal and delicate cycle? is water not draining?

Jan 11, 2009 | Frigidaire ATF6000ES Front Load Washer

2 Answers

Not draining after cycle


try checking the filture on the front at the bottom of the machine they some times get full of muck

Jan 08, 2008 | Hotpoint Aquarius WD63 Front Load...

Not finding what you are looking for?
Whirlpool Duet GHW9150P Front Load Washer Logo

183 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Sal De

Level 3 Expert

2699 Answers

Marvin
Marvin

Level 3 Expert

81423 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1474 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...