Question about Kenwood KDC-MP732 CD Player

1 Answer

WHOULD LIKE TO KNOW WHAT I COULD DO

I CONNECTED AND IT FLASHES PROTECTED ON THE SCREEN

Posted by on

  • Anonymous Mar 11, 2008

    well i connect it and i says protected and i wont do anything

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

This usually happens when there is a short on the speakers or one of those speaker wires is shorted to ground.

Posted on Sep 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My jvc stereo is stuck on protected and it won't change the radio station off protected


Radios that are in "protected" mode often indicate a short in a speaker wire or a really bad speaker. Disconnect all eight speaker wires: white, white/black, gray, gray/black, green, green-black, violet, and violet/black. Turn on the radio and see if it still shows "protected". If it does, the radio is defective. If not, connect each pair of speakers back one at a time and see if it goes into protected mode. The one that causes it is the bad wire/speaker.

Dec 22, 2013 | Car Audio Receivers

1 Answer

I lost code for my sony xr-m510 car radio


what code? as far as i know, i have never seen a sony radio that is code protected.

Dec 12, 2010 | Sony XR-M510 Cassette Player

1 Answer

How do i enter my code in to my car stereo


as far as i know these units are not code protected. what seems to be the problem with the radio>?

Sep 13, 2010 | Clarion XMD3

1 Answer

My stereo flasshes but does not turn on.i have a


it could be that either of the two power wires is loose

Feb 07, 2010 | Boss 640UI CD Player

1 Answer

It says its protected on the screen my battery died due to leavin the lights on!! an i dont know how to get the player to work again!!


If you jump started the vehicle and the radio was on, you may have damaged the unit. If you can remove the radio from the dash, disconnect all power and ground. Let it set for a few minutes then plug it back in. It may or may not turn on. If it still says protect, take the unit to a local car audio shop and ask if they can bench test the unit to make sure that the problem is internal, if so, the average car audio repair is between 100-125 so weigh your options to repair or replace. Hope this helps.

Sep 27, 2009 | Kenwood KDC-MP538U Car CD/ MP3 Player

1 Answer

Display read protected and wont do anything


Usually, protect mode is enabled when the speaker output wiring has shorted together or is touching ground/+12V. I would verify that none of the speaker wiring has come loose.

Mar 19, 2008 | Kenwood KDC-MP5032 - Car Audio CD MP3...

2 Answers

Kenwood kdc 7009 - just bought car w/ stereo in it, but no remote or codes ?


Look for a small hole in the face plate. Take the tip of a pen and try holding it in for a few seconds. Re-setting it should work.....

Jan 26, 2008 | Kenwood KDC-7009

2 Answers

Protected code


this link will help u taking the protected code off good luck

http://inform3.kenwoodusa.com/manuals/KDCMP2032.pdf

Oct 28, 2007 | Kenwood KDC-MP202

Not finding what you are looking for?
Kenwood KDC-MP732 CD Player Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenwood Car Audio Receivers Experts

xxxxxx xxx

Level 3 Expert

4706 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17129 Answers

Pablo Gonzalez

Level 3 Expert

733 Answers

Are you a Kenwood Car Audio Receiver Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...