Question about Hotpoint Aquarius WF000 Front Load Washer

1 Answer

Hotoint 800 delux 9526

How do you take the brushes out

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Get an engineer to do it , much easier , its not hard but for a novice fiddly . an enginner should also bed the new brushes in with a special stone ... i normally charge about 40 pound including parts .

Posted on Apr 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a hotpoint hff31014uk and have no installation guide can't find it anywhere online and can't get through to hotpoint please can anyone help


Double check your model # Hotoint says it's not a valid # then go here for your manual...
http://www.hotpointservice.co.uk/category/refrigeration/

Apr 01, 2016 | Hotpoint Washing Machines

1 Answer

How do i open jammed door on hotoint WD440 washing machine


Some how check to see if it is something in the machine jammed against the door or press on the door while you try to move the unlock lever. Good luck.

Aug 18, 2014 | Washing Machines

1 Answer

Hotoint WMA34 door light keeps flashing and machine wont start


The light flashing usually indicates that the door is not closed securely. this can be caused by a weak or broken door handle spring.
If you are satisfied that the handle is o/k, then the other possibility is that the control module has a blown track, this can be accessed by removing the top cover.
Hope this nhelps.

Jan 15, 2010 | Hotpoint Aquarius WMA42 Front Load Washer

2 Answers

IS A HOTOINT FRONT LOADING WASHER TYPE WF860G [SUPER SILENT] MODEL A HOT/COLD FILL OR COLD FILL ONLY.


This model like most new models are cold fill only.. It will heat to the temperature set by the variable thermostat setting..

Dec 17, 2009 | Hotpoint Ultima WF860 Front Load Washer

1 Answer

I have a Dewalt DW 566 type 3 sds+ drill that runs slow and sparks arround the comutator. Ps I have already fitted new brushes


Take the carbon brushes off one at a time. Clean the
commutator by Grit 800 sandpaper to clear it from carbon deposits. You can manually rotate the drill to have it clear from carbon deposits. Thereafter clean it
further by cotton cloth. Sparks will now be minimized
until the brush is fully seated on the commutator.

Nov 22, 2009 | Washing Machines

2 Answers

CAN ANYONE PLEASE TELL ME WHERE THE FILTER IS SITUATED. Thanx.


They are normally behind the "kick" panel that runs the width of the machine on the front. just pull the panel off, grab each end and pull straight off tilting slightly up as you pull. on the right hand side as you look at it you should see the filter.

May 01, 2009 | Washing Machines

1 Answer

No instructions


Go to:
www.hotoint.co.uk.
Scroll down and click on www.hotpoint.co.uk.
Click on after sales and then click on down load instruction books, type your model number in and you can save it to your hard drive, or print it off.
Plz rate my solution.
Thanks.

Dec 16, 2008 | Hotpoint First Edition WMA12 Front Load...

1 Answer

Main motor carbon brush


easier to remove the motor. the brushes are held in by 2 small bolts for each

Sep 04, 2008 | Hotpoint First Edition FEW12 Front Load...

1 Answer

All Lights Flashing on Hotoint Aquarious WF310 Washing Machine


Means that the heat sensor is broken.
Replace that and it should fix your problem

May 09, 2008 | Hotpoint Aquarius WF000 Front Load Washer

Not finding what you are looking for?
Hotpoint Aquarius WF000 Front Load Washer Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

hungoverrr

Level 1 Expert

5 Answers

puggy666

Level 1 Expert

47 Answers

gbob59

Level 3 Expert

2963 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...