I have no instructions for my p110i i have a cleaning kit but obviously dont know how to use it

It sounds like you might have a job stuck in the print-queue. Best way to check is to start with a clean slate:

1. Shut-down your badge-software, and disconnect the printer from its power source;
2. Navigate to the Windows print center - accessible from the Control Panel as "Printers & Faxes" if Windows-XP, or "Devices and Printers" if Windows 7.
3. Right-click on your Zebra P110i printer, and select "See What's Printing" to open the queue, and see if there are jobs there. If so, click "Printer" on the menu, and then "Cancel all Document".
4. You also should ensure that you don't have any additional instances of the printer drive installed - they would show up as Zebra P110i (Copy 1), ... (Copy 2), etc. This occurs within Windows if you've disconnected the PC-end of the USB cord, and then plugged into a different USB port than originally used. If you have multiple instances, the easiest way to clean this up is to right-click on each sequentially, selecting "Remove this Device". Do this for each one.
5. Now you have a "clean slate". Connect the Zebra printer to the PC's USB, and then re-connect the power. If it doesn't power on, push the power button so it is on.
6. WAIT until Windows recognizes the pritner and you see the device is ready to use.
7. Open your badge software, and select a single card to print, and send it to the printer. If all goes well, this single card will print correctly, then the printer will come back to a ready status. Repeat for a second card, and make sure it prints correctly, and comes back to ready. If all is good, you've likely cleared the issues up, and you can proceed normally. If not, then there may be a physical problem with the printer, where it is not recognizing that a finished card has been ejected and the job is done, or it's not communicating that "done" status back to the host PC.

possible solution

go to solutionmanual with given link

http://www.google.co.in/url?sa=t&rct=j&q=&esrc=s&frm=1&source=web&cd=1&ved=0CHQQFjAA&url=http%3A%2F%2Fwww.zebra.com%2Fid%2Fzebra%2Fna%2Fen%2Fdocumentlibrary%2Fmanuals%2Fen%2Fprinter_manuals%2Fp110i_p110m_user_manual.File.tmp%2FP110i_P110m_en.pdf%3Fdvar1%3DProductLiterature%26dvar2%3DP110i%2520and%2520P110m%2520User%2520Manual%2520(en)%26dvar3%3D10304&ei=KJCzT8nxA8LIrQfk3_iTBA&usg=AFQjCNH7-Exi1kBs6bM4pVi3ZLTMG8QkWQ&sig2=8Dlib_NW13l5-cQa7UjIWg


rply me soon

Check the type of cards you are using, they might be too thick. If you are using the regular 30mil PVC Cards then make sure before you load the cards you "fan" them, meaning try to separate the cards as when they build static electricity and "glue" to each other.

If that does not solver your problem, then you should send the printer for repairs, check your warranty status with your ID Printer Vendor.

Also, sometimes if you are using the Adhesive cards, the paper back of the card does not feed into the roller system of the printer.

-- The Pros at www.DiscountIDStore.com

On your cardfive configuration for the printer, there might be 2 printer drivers in the drop-down list, you might have the wrong one selected.

-- The Pros at www.DiscountIDStore.com

The Zebra P110i printer is an Edge-To-Edge card printer, which means it will print on the card closest to the edge as possible, however there will still be a slight line. Although a 2mm line is too big, should be no more than 1mm, there will still always be a line.

There are some advanced EC (end card) settings that could be adjusted but if the print goes too close to the edge, the ribbon will get cut.

-- The Pros at www.DiscountIDStore.com

No

---

Please dont forget to vote if you liked my answer

thanks

Looks like what you need is available at

http://www.serviceforce.co.uk/pdfs/U20206.pdf

Good luck with the new house. Hope the dishwasher works well for you.

Try to run it with dishwasher cleaning kit (no utensils) to make sure everything is clean - that way you will get more life out of it. The cleaning kit (usually Finish) is sold in the supermarket in the detergent section.

Yes its a easy an inexspensive repair. www.tvrepairworld.com has the ITC222 and ITC222A convergence option missing repair kit. The kit contains the parts and CD with instructions.

http://www.youtube.com/watch?v=CzGXjl4Rv1

Where did you purchase the kit? Can you name the store with number or list the website? Also the part number information. Thanks